background image

Resolution

1. Enable LiteLOC.

When LiteLOC is enabled, a warning is presented if color cannot be maintained due to
temperature or humidity levels being problematic.

2. If possible, implement changes to stabilize the room temperature or raise the expected

ambient temperature.

3. If possible run the projector in an environment with less than 80% relative humidity.
4. If the brightness slider is too low, select MENU > Configuration > Light & Output

Settings > LiteLOC > Master Laser Power to increase the brightness.

5. If you changed the brightness or color points, wait 5 to 10 minutes for them to stabilize.

Colors on the screen not accurate

The colors on the screen are not as expected.

Details

Possible causes include:

The color correction modes were not selected to match the content playing on the screen.

The precise color chromaticity was either set up wrong or not enabled.

Resolution

1. Disable the existing color settings by doing a factory default of the system.
2. Set up laser configuration, color correction mode, and primary color settings. Evaluate the

image.

Blemishes appearing on the screen

Blemishes or color blotches are appearing on screen.

Details

Possible causes include:

Contamination on the light engine, projection lens, or other topical surfaces that light passes
through after the lens.

A broken diffuser can cause color blotches.

Resolution

1. Clean the optical surfaces.
2. If the issue persists, an optics failure may be indicated. Contact Technical Support.

4K40-RGB troubleshooting

4K40-RGB Technical Reference–Troubleshooting

13

020-103239-01 Rev. 1 (09-2020)

Copyright 

©

 2020 Christie Digital Systems USA, Inc. All rights reserved.

Содержание Mirage 4K40-RGB






















Отзывы: