background image

AC power precautions

Read all safety and warning guidelines before connecting to AC power.

Warning! If not avoided, the following could result in death or serious injury.

SHOCK HAZARD! Only use the AC power cord provided with the product or recommended by
Christie.

FIRE AND SHOCK HAZARD! Do not attempt operation unless the power cord, power socket, and
power plug meet the appropriate local rating standards.

SHOCK HAZARD! Do not attempt operation if the AC supply is not within the specified voltage
and current, as specified on the license label.

SHOCK HAZARD! The optional UPS power cord must be inserted into an outlet with grounding.

SHOCK HAZARD! Disconnect the product from AC before installing, moving, servicing, cleaning,
removing components, or opening any enclosure.

Install the product near an easily accessible AC receptacle.

Caution! If not avoided, the following could result in minor or moderate injury.

FIRE HAZARD! Do not use a power cord, harness, or cable that appears damaged.

FIRE OR SHOCK HAZARD! Do not overload power outlets and extension cords.

SHOCK HAZARD! Power supply uses double pole/neutral fusing.

Light intensity hazard distance

This projector has been classified as Risk Group 3 as per the IEC 62471-5:2015 standard due to

possible hazardous optical and thermal radiation being emitted.

Warning! If not avoided, the following could result in serious injury.

PERMANENT/TEMPORARY BLINDNESS HAZARD! No direct exposure to the beam must be
permitted. Class 1 Laser Product - Risk Group 3 according to IEC 60825-1:2014 and IEC
62471-5:2015.

PERMANENT/TEMPORARY BLINDNESS HAZARD! Operators must control access to the beam
within the hazard distance or install the product at the height that prevents exposure of
spectators' eyes within the hazard distance. The hazard zone must be no lower than 2.5 meters
(US installations) or 2.0 meters (global installations) above any surface upon which any persons
are permitted to stand and the horizontal clearance to the hazard zone must be a minimum 1.0
meters.

EXTREME BRIGHTNESS! Do not place reflective objects in the product light path.

The following diagram and table show the zones for ocular and skin hazard distances:

Safety precautions

C 4K-RGB Installation and Setup Guide–CP4415-RGB, CP4420-RGB

6

020-103244-04 Rev. 1 (03-2021)

Copyright 

©

 2021 Christie Digital Systems USA, Inc. All rights reserved.

Содержание CineLife+ 4K-RGB




























































Отзывы: