background image

                                                                 

 

Quad-Band 

850/900/1800/1900Mhz   

GPS chip 

UBLOX Chip 

GPS sensitivity 

-159dBm 

GPS accuracy 

5m 

Time To First Fix 

Cold status    27s    Warm status    27s    Hot status    1s 

Car charger 

12—24V    input    /    5V     output 

Wall charger 

110

220V    input    /    5V     output 

Battery 

Chargeable changeable 3.7V 800mAh Li-ion battery 

Standby 

80hours 

Storage Temp. 

-40°C to +85°C 

Operation Temp. 

-20°C to +55°C 

Humidity 

5%--95% non-condensing 

6.

 

SIM/SD CARD Installations 

The SIM CARD Installation Steps: 

Open the rear cover, and pick out the battery. Push the foil along and turn it left. Put the SIM card 
into the holder, and turn the foil right and fasten it in place. 

Attentions:   

 

Please don't insert, change or remove SIM card when the GPS device is working. If you need to 
this, please confirm that the device is power off. 

 

Please make check SIM card and make sure that incoming calls display is available, call transfer is 
forbidden and the PIN code is locked.   

 

The SMS must be TXT format; The PDU format will not be supported by device. 

 

Please ensure that GPRS function of your SIM card is available. The GSM base station location 
and the communication between the tracking software/server and the device need to be supported 
by GPRS function. (If your device only work in SMS control mode, the GPRS function is 
unnecessary). 

 

The tracking device only supports GSM network. WCDMA or other 3G SIM cards are not 
supported. 

The SD CARD Installation Steps: 

Insert the SD card (Micro SD card) into the corresponding card slot in the correct direction. If you 
need to remove the SD card from the device, just press the SD card and it will pop up 
automatically. 

Attentions: 

 

Please don't insert or remove the SD card when the GPS device working. If you need do this, 
please confirm that the device is power off.   

 

Maximum capacity of SD card is up to 32GB; 

 

In order to read the data in SD card, you can connect the device to the computer with the USB 
cable. You can also plug out the SD card when the device is power off, and use a SD card reader.   

As shown in Figure; 

Open the SIM Card Slot.                                Install the SIM card and SD card to slot.

 

             

 

Содержание RX102


















Отзывы: