Chiltrix CX34-4 Скачать руководство пользователя

Страница: 13 / 54

Chiltrix Inc.

www.chiltrix.com

Chiltrix Heat Pump Installation

Heat Pump Installation

Installation position

Note:

Installation must be carried out by professional personnel.

The recommended mounting pad should be at least 1 ½” above ground level. If you are in an area where snow

occurs, mount the unit high enough above grade to avoid blockage by drifting snow. You can consider a

properly rated wall mount if desired.

Proper drainage is required at the heat pump unit to avoid flooding the outdoor unit with water or ice. Make

sure condensate has a way to rapidly and completely drain away from the unit.

To install the unit on a balcony or on top of a building, the installation site must meet the allowable load

bearing capacity of the building structure without affecting the structural safety. Ensure the unit is well

ventilated; the direction of air exhaust should be kept away from the windows of neighboring buildings.

Adequate service clearance should be kept around the unit. The unit should not be installed in places

accompanied with oil, inflammable gases; corrosive components e.g. sulfur compound, or high-frequency

equipment.

Outdoor Unit Placement / Clearances

(Unit: mm) 200mm = 8” , 350mm =14 “,

400=16”, 500=20”,1000=40”

Содержание CX34-4























































Результаты поиска

Содержание CX34-4

Отзывы:

Похожие инструкции для CX34-4

Бренды по названию

Популярные бренды

Chiltrix CX34-4, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CX34-4

Отзывы:

Похожие инструкции для CX34-4

Бренды по названию

Популярные бренды