H03743:11/04
6
O
MAINTENANCE OF YOUR BED:
Upon completion of assembly be sure all screws, bolts and fastening devices have been
tightened securely. A frequent check should be made of all screws, bolts and fastening devices and tightened if needed. Before
each usage or assembly, inspect crib for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT
use crib if
parts are missing or broken. Contact Child Craft at 1-877-265-9046 or
http://www.childcraftindustries.com
, for a replace-
ment part or instructional literature if needed. Include Model Identification Number with your request which you recorded on
Page 2 of these instructions.
DO NOT SUBSTITUTE PARTS.
DO NOT MAKE ANY ALTERATIONS NOT DESCRIBED IN
THESE ASSEMBLY DIRECTIONS.
O
CLEANING INSTRUCTIONS FOR YOUR BED:
Mix together a mild solution of gentle dishwashing liquid and water, apply to
surface using a soft clean cloth lightly dampened in the solution. Rinse with clear water again using a soft clean cloth, then dry
all surfaces thoroughly with a soft dry cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL, OR COARSE
RAGS SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
O
STORAGE AND USE OF YOUR BED:
A printed plastic pouch is attached to the crib spring for the permanent storage of the
assembly directions. After completing the assembly process you are advised to read and be aware of all
WARNINGS, CAU-
TIONS, CLEANING, STORAGE, USE AND MAINTENANCE
notices contained in this set of directions and printed on the plastic
pouch located on the underneath side of the crib spring. You will then place the complete set of assembly directions into the
plastic pouch for future referral. We caution you not to place excess hardware in the plastic pouch as it could present danger to
a child if retrieved. When storing crib use
CAUTION
as extreme temperature or humidity changes could be harmful. Use
CAUTION
when a vaporizer is in use, always aim vapor stream away from crib as well as away from any wood furniture item.
S
AVE
THESE
INSTRUCTIONS
AND
ALL
PARTS
FOR
FUTURE
USE
C
ONVERT
TO
T
ODDLER
B
ED
When use as a crib has been completed, you have the option to convert to a Toddler Bed for years of additional use in your child’s
room. Refer to
Step 4 - Diagram 4.
Remove Stationary Side Left
L
or Stationary Side Right
K
. Install Crib Stretcher
Q
as shown
in
Sketch A
. Dowel on Stretcher
Q
locates in bottom hole at bottom of Posts
O
&
P
, then secure with Allenhead Bolts
H
.
Spring
R
R
R
R
R
must be installed in lowest position.
Store the removed parts and hardware in the event you wish to convert your Toddler Bed
back to a crib.
Sketch A
(style may vary)
NOTE: When using as a Toddler Bed the
mattress must have minimum dimensions
of 51-5/8 in. (1310mm) in length and 27-1/4
in. (690mm) in width and 4 in. (100mm) in
thickness but not to excees 6 in.
It is very important that the Stretcher
Q
Q
Q
Q
Q
is
used when converting to a Toddler Bed.
Failure to install this part could result in
serious injury or death.
When using as a Toddler bed, the mini-
mum age shall not be less than 15 months
and the maximum weight shall not be
greater than 50 lb (22.7 kg).
WARNING
V
!
Q
Spring
R
must be installed in lowest position.
Purchased Mattress see
size requirements under
W
ARNING
CHILD CRAFT INDUSTRIES, INC.
P.O. BOX 444
SALEM, IN 47167-0444 USA
PH:812-883-3111
FAX:812-883-1819
http://www.childcraftindustries.com
L
