CHIEF JWP-V Скачать руководство пользователя

Страница: 11 / 14

Installation Instructions

JWP-V

300mm x 200mm Pattern

For the 300mm x 200mm hole pattern, do the
following:

1. Select eight Phillips head M6 screws (110) from

Bag B and eight spacers (120) from Bag C.

2. Attach the interface bracket (20) using the hole-

pattern on the back of your display as shown in
Figure 7.

3. Tighten each screw. To prevent equipment damage,

do not over-tighten the screws.

400mm x 200mm Pattern

For the 400mm x 200mm hole pattern, do the
following:

1. Select six Phillips head M6 screws (90) from Bag B

and six spacers (120) from Bag C.

2. Attach the interface bracket (20) using the hole-

pattern on the back of your display as shown in
Figure 8.

3. Tighten each screw. To prevent equipment damage,

do not over-tighten the screws.

Figure 7. Display with 300mm x 200mm Hole Pattern

Figure 8. Display with 400mm x 200mm Hole Pattern

Содержание JWP-V















Результаты поиска

Содержание JWP-V

Отзывы:

Похожие инструкции для JWP-V

Бренды по названию

Популярные бренды

CHIEF JWP-V, Руководство по установке

Результаты поиска

Содержание JWP-V

Отзывы:

Похожие инструкции для JWP-V

Бренды по названию

Популярные бренды