CHIEF JWP-V Скачать руководство пользователя

Страница: 14 / 14

Installation Instructions

JWP-V

CABLE MANAGEMENT

WARNING:

Make sure your cables do not run

through a pinch points. Do not put your fingers
between movable parts.

For cable management (not shown), connect and
secure power/audio/video cables, making sure to
leave sufficient slack to allow for movement of the
display.

ADJUSTMENTS

Lateral Tension Adjustment

To adjust Lateral Tension:

1. Move arms laterally to check for desired tension.

2. Using a 3/16” hex wrench slightly tighten or loosen

lateral tension adjustment bolts (seeFigure 14).

3. Repeat Steps 1 and 2 until desired tension is

obtained.

Pitch Tension Adjustment

To adjust Pitch Tension:

1. Tilt display to check for desired tension.

2. If pitch tension in Centris Bracket requires

adjustment, perform the following steps:

Remove Display from Centris Bracket.

Using a 3/16” hex wrench, slightly tighten or
loosen pitch adjustment bolt to adjust Centris
Bracket as needed (see Figure 15).

Reinstall display.

3. Repeat Steps 1 and 2 until desired tension is

obtained.

Figure 14. Adjust Lateral Tension

Figure 15. Adjust Pitch Tension

Pitch Adjustment Bolt

Lateral Tension Adjustment Bolt

Содержание JWP-V















Результаты поиска

Содержание JWP-V

Отзывы:

Похожие инструкции для JWP-V

Бренды по названию

Популярные бренды

CHIEF JWP-V, Руководство по установке

Результаты поиска

Содержание JWP-V

Отзывы:

Похожие инструкции для JWP-V

Бренды по названию

Популярные бренды