Chicago Pneumatic CPS 185 PD7 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 30

background image

20

1310 3012 08

4.3 Lubrication oils

It is strongly recommended to use Chicago Pneumatic branded lubrication oils for compressor.
Compressor oil

GENOIL - M

:

1 gallon pail:

order number

1626 2260 00

5 gallon pail:

order number

1626 2261 00

Compressor oil

GENOIL - S

:

5 gallon pail:

order number

1626 2264 00

Engine OIL:

GEN OIL 15W40

1 gallon pail:

order number

1626 2262 00

5 gallon pail:

order number

1626 2263 00

GEN OIL 5W40

1 gallon pail:

order number

1626 2258 00

5 gallon pail:

order number

1626 2259 00

Type of Oil

Temperature Range

Compressor Engine

Between -13°F and 122°F

(1)

Gen OIL S

See Engine Operation Manual

Between 18°F and 104°F

Gen Oil M

15W-40

(1)

Additional equipment is needed to run the compressor below 18°F. Please contact Chicago Pneumatic for more

information about Cold Weather Packages.

f

Operation of compressor in ambient temperatures lower than 18°F (-8°C) without the correct type of oil
will void your warranty and may result in element failure and/or fire.

Oil Level Check

f

Never mix oils of different brands or types

4.3.1 Check Engine Oil Level

Consult also the Engine Operation Manual for the oil specifications, viscosity recommendations and oil change intervals.
See schedule.
Check engine oil level according to the instructions in the Engine Operation Manual and top up with oil if necessary.

4.3.2 Check Compressor Oil Level

With the unit standing level, engine stopped, check the level of the compressor oil. The pointer of the oil level gauge (OLG) must
register in the upper extremity of the green range. Add oil via the oil fill plug (FP) if necessary.

f

Before removing oil filler plug, ensure that the pressure is released by opening an air outlet valve.

4.3.3 Engine Oil And Oil Filter Change

Consult also the Engine Operators Manual for oil and oil filter

(1) change

intervals.

(2) oil

types.

4.3.4 Compressor Oil And Oil Filter Change

The quality and the temperature of the oil determine the oil change interval.

The prescribed interval (See section 4.2) is based on an oil temperature of up to 100ºC (212ºF) and normal operating conditions.

When operating in high ambient temperatures, in very dusty or high humidity conditions, it is recommended to change the oil more
frequently.

«
...
18
19
20
21
22
...
»

Содержание CPS 185 PD7































Отзывы:

Нет отзывов

Похожие инструкции для CPS 185 PD7

Бренд: Gardner Denver Страницы: 26

210/08/24 12-TLG

Бренд: Gude Страницы: 59

Бренд: Jet Страницы: 22

Бренд: VIAIR Страницы: 8

Бренд: Champion Страницы: 32

Бренд: Champion Страницы: 32

Бренд: Champion Страницы: 36

Бренд: Champion Страницы: 40

Бренд: Champion Страницы: 44

Бренд: Speedaire Страницы: 48

Bock F76 Series

Бренд: GEA Страницы: 28

Бренд: Zanotti Страницы: 76

Бренд: KAESER KOMPRESSOREN Страницы: 24

Бренд: NARDI COMPRESSORI Страницы: 52

Бренд: Dangerous Music Страницы: 19

BOCK UL-HGX24e CO2 LT

Бренд: Danfoss Страницы: 36

Бренд: Ingersoll-Rand Страницы: 75

Бренд: Ingersoll-Rand Страницы: 91

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды