background image

SKU 93449

For technical questions please call 1-800-444-3353

Page 6

Working with the Rechargeable Battery

Charging the Battery Pack:

1.

Battery Packs are normally shipped with low or no charge to prevent potential

problems during shipment. Before use, you must charge your new Battery Pack.
Initial charge time is approximately 1-½ hour. Subsequent recharge time is
approximately 1-½ hour.  New Battery Packs will not hold a charge as long as
older ones. Completely deplete and recharge Battery Pack several times to
extend its charge life.

2.

Plug the battery charger into a 120 VAC, 60 Hz power outlet, the Green LED will

illuminate.

3.

Insert the Battery Pack into the charger by aligning the rib on the Battery Pack

with the groove in the charger. Press the Battery Pack into place. The Green
LED will shut off and the Red LED will illuminate indicating that a Battery Pack
is installed in the charger, and that it has started charging.

NOTE: 

During recharging, the Battery Pack will become slightly warm to the touch.

This is normal and not a cause for concern. Do not keep the Battery Pack or
charger in an environment of extreme heat or cold. They will work best at room
temperature.

4.

The red LED will remain on for approximately 1 hour while the Battery Pack

charges.  When the Battery Pack is fully charged the Red LED will go out, and
the Green LED will illuminate indicating that the Battery Pack is fully charged.

5.

When the Battery Pack is fully charged, remove the charged battery from the

charger, and unplug the charger from its power source. Put the charger away for
safekeeping. Do not leave the Battery Pack in the charger indefinitely.

Installing the Battery Pack

1.

Slide the Battery Pack onto the rail of

the body before pressing it into the
handle. 

CAUTION:

 Do not press the

battery into the handle if it is not
properly aligned on the rail, as this may
damage the body of the tool, and will
not secure the battery.

2.

With the Battery Pack properly

aligned on the rail, press into place
in the handle.

Installing the Battery Pack

Содержание 93449













Отзывы: