Chicago Electric 66603 Скачать руководство пользователя страница 5

Страница: 5 / 28

Page 5

SKU 66603

For technical questions, please call 1-800-444-3353.

If an appliance begins to operate abnormally, becomes sluggish or stops suddenly,

turn it off immediately. Disconnect the appliance, and determine whether the

problem is the appliance, or if the rated load capacity of the generator has been

exceeded.

Make sure that the electrical rating of the tool or appliance does not exceed that of

the generator. Never exceed the maximum power rating of the generator. Power

levels between rated and maximum may be used for no more than 30 minutes.

Substantial overloading will open the circuit breaker. Exceeding the time limit for

maximum power operation or slightly overloading the generator may not switch

the circuit breaker or circuit protector OFF, but will shorten the service life of the

generator.

sERvIcE

Tool service must be performed only by qualified repair personnel.

Service or

maintenance performed by unqualified personnel could result in a risk of injury.

when servicing a tool, use only identical replacement parts. Follow

instructions in the

“Inspection, Maintenance, And Cleaning”

section of this

manual.

Use of unauthorized parts or failure to follow maintenance instructions

may create a risk of injury.

spEcIFIc sAFETY RUlEs

IMpoRTANT! Your warranty is voided if:

You do not put engine oil in the Engine’s crankcase prior to its first use.

Before each use, check the oil level. Never run the Engine with low or no engine

oil. Running the Engine with low or no Engine oil will permanently damage the

Engine.

Maintain labels and nameplates on the Generator.

These carry important

information. If unreadable or missing, contact Harbor Freight Tools for a

replacement.

Maintain a safe working environment.

Make sure there is adequate surrounding

workspace.

Avoid unintentional starting.

Make sure you are prepared to begin work before

turning on the Generator.

people with pacemakers should consult their physician(s) before use.

Electromagnetic fields in close proximity to a heart pacemaker could cause

pacemaker interference or pacemaker failure. Caution is necessary when near

the Engine’s magneto or recoil starter.

Содержание 66603





























Результаты поиска

Содержание 66603

Отзывы:

Похожие инструкции для 66603

Бренды по названию

Популярные бренды

Chicago Electric 66603, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 66603

Отзывы:

Похожие инструкции для 66603

Бренды по названию

Популярные бренды