Chicago Electric 66603 Скачать руководство пользователя страница 2

Страница: 2 / 28

Page 2

SKU 66603

For technical questions, please call 1-800-444-3353.

spEcIFIcATIoNs

Electrical Requirements

6500 Rated Watts (Rated) / 7000 Maximum Watts (Maximum) / 60 Hz / 3600 RPM

output Receptacles:

2 NEMA 120V, Household Receptacles, with a 20 A Circuit Breaker

1 NEMA 120V, 3-Prong Twist Lock Receptacles with a 30 A Circuit Breaker

1 NEMA 120V/240V, 4-Prong Twist Lock Receptacles with two 30 A Circuit Breakers

Input power:

12 VDC Battery / 7-1/4” Long x 3” Wide (not included) with an In-Line

Circuit Breaker

voltmeters:

0 < - > 150 Volts / 50 Volt Marked Increments

0 < - > 300 Volts / 100 Volt Marked Increments w/50 Volt Hash Marks

Engine Specifications

16 HP / 4 Cycle / Air Cooled / Electric & Recoil Start / 3600 RPM

420cc Displacement / 6.6 Gallon Fuel Tank

Powered with Mid to High Octane, Unleaded Gasoline

Engine Family: 5CSG.41925C

Recommended oil:

37 Fluid Ounces

SAE 30W (Above 32 Fahrenheit) / SAE 5W-30 (Below 32 Fahrenheit)

Recommended Spark Plug Gap: 0.028” ~ 0.031”

Estimated Run Time: 8 Hours @ 50% Load

Automatic Low Oil Shutdown

Additional Features

Locking ON/OFF with 2 Keys

Overall Dimensions

24-1/8” Long x 20-1/2” Wide x 24-1/2” High

Net Weight

205 Pounds

IMpoRTANT!

This product requires oil and fuel to be added before starting. Attempting to start

the Engine without oil WILL ruin the Engine and void the warranty.

NoTE:

The Engine’s carburetor may need to be adjusted by a qualified mechanic for efficient

high-altitude use.

The emission control system for this Generator’s Engine is warranted for standards set by

the U.S. Environmental Protection Agency. For warranty information, refer to the last pages of

this manual.

sAvE ThIs MANUAl

You will need this manual for the safety warnings and precautions, assembly, operating,

inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your

invoice with this manual. Write the invoice number on the inside of the front cover. Write the

product’s serial number in the back of the manual near the assembly diagram, or write month

and year of purchase if product has no number. Keep this manual and invoice in a safe and dry

place for future reference.

REV 09l

Содержание 66603





























Результаты поиска

Содержание 66603

Отзывы:

Похожие инструкции для 66603

Бренды по названию

Популярные бренды

Chicago Electric 66603, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 66603

Отзывы:

Похожие инструкции для 66603

Бренды по названию

Популярные бренды