Chicago Electric 66603 Скачать руководство пользователя страница 3

Страница: 3 / 28

Page 3

SKU 66603

For technical questions, please call 1-800-444-3353.

GENERAl sAFETY RUlEs

wARNING!

READ AND UNDERsTAND All INsTRUcTIoNs

Failure to follow all instructions listed below may result in

electric shock, fire, and/or serious injury.

sAvE ThEsE INsTRUcTIoNs

woRK AREA

Keep your work area clean and well lit.

Cluttered and dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust.

Power tools create sparks which may ignite the dust

or fumes.

Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control. Protect others in the work area from debris

such as chips and sparks. Provide barriers or shields as needed. Children should never

be allowed in the work area.

pERsoNAl sAFETY

stay alert. watch what you are doing, and use common sense when operating a

power tool. Do not use a power tool while tired or under the influence of drugs,

alcohol, or medication.

A moment of inattention while operating power tools may result

in serious personal injury.

Dress properly. Do not wear loose clothing or jewelry. contain long hair. Keep

your hair, clothing, and gloves away from moving parts.

Loose clothes, jewelry, or

long hair can be caught in moving parts.

Remove adjusting keys or wrenches before turning the power tool on.

A wrench or a

key that is left attached to a rotating part of the power tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times.

Proper footing and

balance enables better control of the power tool in unexpected situations.

Use safety equipment. Always wear eye protection.

Dust mask, nonskid

safety shoes, hard hat, or hearing protection must be used for appropriate

conditions.

Tool Use And care

Do not force the tool. Use the correct tool for your application.

The correct tool will

do the job better and safer at the rate for which it is designed. Do not force the tool and do

not use the tool for a purpose for which it is not intended.

Содержание 66603





























Результаты поиска

Содержание 66603

Отзывы:

Похожие инструкции для 66603

Бренды по названию

Популярные бренды

Chicago Electric 66603, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 66603

Отзывы:

Похожие инструкции для 66603

Бренды по названию

Популярные бренды