Chevrolet IMPALA 3.9L 2009 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 32

Chevrolet IMPALA 3.9L 2009 Скачать руководство пользователя страница 25

©

2009 IMPCO Technologies, Inc.

-23-

2009 3.5/3.9L Impala CNG

N. Sequent Component Electrical Connections:

1) Connect the Sequent injector connectors.

Match the number on the injector wiring to
the CNG injector as illustrated.

Failure to follow this order will result in a rough
fuel change over and reduced performance on
CNG. Refer to the

2009 3.5L Impala P&D

Installer’s Wiring Diagram

for additional

information.

2) Connect the fuel temperature / pressure

sensor.

3) Connect the regulator temperature sensor.
4) Connect lockoff.
5) Connect the Sequent ECM.

O. Final

Connections:

1) Connect the high pressure CNG line to the

lockoff. Leak test the entire Sequent and
OEM fuel systems with applicable code
approved equipment before starting the
engine.

2) Reconnect all OEM components except for

the engine cover.

3) Reinstall the battery. If the installation

requires the Sequent B+ and B–
connections be made at the battery,
connect them now.

P. Fuel Level Calibration:

1) Perform the fuel level calibration as

described in the

Sequent P&D Display

Software User Manual.

«
...
23
24
25
26
27
...
»

Содержание IMPALA 3.9L 2009

































Отзывы:

Нет отзывов