Chevrolet 1997 Corvette Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 41

Chevrolet 1997 Corvette Скачать руководство пользователя страница 37

3-36

1997/98 Chevrolet Corvette

Collision Repair

Fig.␣ 3.76 — Bond Rear Compartment Panel to Top Side at Impact Bar

8

Apply a thin coat of Goodwrench Structural
Bonding Epoxy (part no. 1234526), or
equivalent, to the entire repair area
extending across the cut lines, use tacky
mesh tape or an equivalent reinforcement
matting. Apply enough bonding epoxy to
fully ‘wet out’ reinforcement matting. Allow
to cure as necessary.

(Refer to SMC Repair

Procedures.)

9

Scuff all bonding surfaces to ensure proper
adhesion.

(Refer to SMC Repair Procedures.)

10

Clean and prepare all bonding surfaces as
necessary.

(Refer to SMC Repair Procedures.)

11

Apply a bead of urethane adhesive to bond
the impact bar to the rear compartment as
shown in Fig.␣ 3.76. This is a structural bond,
and care must be used to ensure that the
adhesive fills the gap adequately.

12

Finish and feather-edge the repair areas as
necessary to resemble OEM.

13

Prime the SMC repair areas with a suitable
primer. Apply appropriate sealers .

14

Apply top-coat over all repaired areas. Refer
to paint manufacturer’s recommendations.
Do not combine paint systems.

15

Install all related panels and components.

Rear Bumper Impact Bar

«
...
35
36
37
38
39
...
»

Содержание 1997 Corvette










































Отзывы:

Нет отзывов