manualshive.com logo in svg

Chevrolet 1997 Corvette, Полное руководство, Страница: 15 / 41

Поделиться
Скачать
Chevrolet 1997 Corvette Скачать руководство пользователя страница 15

3-14

1997/98 Chevrolet Corvette

 

Collision Repair

FRT

Fig.␣ 3.26 — Shaded Areas Are High-Strength Steel

Rail-Underbody Side Assembly

— INSTALL OR CONNECT —

1

Replace door side frame and the lock pillar
extension panels. (

Refer to Door Side Frame

Service Procedures.)

2

Replace floor panel and lower floor panel
extension at factory seams. (

Refer to Floor

Panel Service Procedures.)

3

After sectioning repairs are completed,
attach panels and components as necessary.

Rear Rail Repair

When damage to the frame rail is limited to the
portion rearward of the seat back area. The seat
back sectioning area is exposed by modifying or
removing close-out panels and tunnel braces for
access to all sides of the rail. There are some high
strength steel panels located in the rear of the
vehicle which can be repaired if damage excludes
kinks, or damage which would require the use of
heat to straighten (Fig.␣ 3.26).

Notice: Check front of dash panel, floor
panels, and all other SMC for cracks or areas
that may need to be repaired or resealed.
(Refer to SMC Repair Procedures.)

Notice: Use the Offset Lap-Joint method to
perform rear rail repairs.

Содержание 1997 Corvette










































Отзывы:

Нет отзывов