background image

TM-G746A Rev.: B 

DCR# 17-0231  

DATE: 3/21/17 

Federal Identification Code: 11815 

© 2017 Cherry Aerospace 

14 

 
 

 

PRIMING THE HYDRAULIC SYSTEM 

    

RECOMMENDED HYDRAULIC FLUID 

 

The riveter is supplied with 

Dexron® III ATF type “A”

.

 

 

COMPATIBLE ALTERNATE FLUIDS  

 

Automatic Transmission Fluids:

 DEXRON IV, MERCON, Allison C4 or equivalent. 

 

Hydraulic Fluids:

 Hyspin® VG32 , Aeroshell fluid 4 

 

 CAUTION 

 

 

DO NOT MIX DIFFERENT TYPES OF HYDRAULIC OILS AND TRANSMISSION; HYDRAULIC AND TRANSMISSION 
FLUIDS ARE NOT COMPATIBLE DIFFERENT TYPES OF FLUIDS MAY NOT BE COMPATIBLE WITH EACH OTHER.

 

 

PHYSICAL PROPERTIES AND MATERIAL SAFETY DATA SHEETS FOR DIFFERENT FLUIDS MAY DIFFER FROM THE 
ONE GIVEN BELOW, BUT THE SAFETY INFORMATION STILL APPLIES; CHECK WITH THE FLUID MANUFACTURER 
FOR ADDITIONAL MSDS AND SPECIFIC PROPERTIES.

 

FLUID HANDLING SAFETY 

 

ENVIRONMENTAL

 

 

 

Waste Disposal in accordance with the applicable regulations 

 

 

Soak up spills with diatomaceous earth or other inert materials. 

 

Keep from drains, sewers and water courses.  

 

Filter and recycle used fluid; otherwise store and dispose of 
according to the applicable regulations. 

 

HANDLING

 

 

 

Eye protection is required.  

 

Protective gloves, chemically resistant boots and apron are 

recommended.  

 

FIRST AID 

 

 

Flush eyes thoroughly with water. 

 

If irritation develops, consult a physician. 

 

 

To prevent inhalation, use in well-ventilated area. 

 

Short term exposure should pose no adverse health effects. 

 

If inhalation occurs, remove the affected person from the 

contaminated area and apply artificial respiration if needed. 

 

 

DO NOT INDUCE VOMITING. 

 

Seek medical attention immediately. 

 

In case of skin contamination: 

 

Wash thoroughly with soap and water as soon as possible.  

 

Brief skin contact requires no immediate attention.  

 

If irritation develops, consult a physician. 

 

COMBUSTIBILITY

 

 

 

It is slightly combustible when heated above flash point.  

 

It will release flammable vapors which can burn in open or be 

explosive in confined spaces if exposed to source of ignition. 

 

Do not store near open flames or other sources of ignition. 

 

 

In case of fire, use only suitable extinguishing media:  
CO2, dry powder, foam or water fog.  

 

CAUTION: DO NOT USE WATER JETS. 

 

Specific gravity: 

0.863 

Weight per gallon: 

7.18 lbs. 

Open flash point: 

>200°C (392°F) 

 

Содержание CHERRYMAX G746A

















Отзывы: