Chemtrac SCC3500XRD Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 58

Chemtrac SCC3500XRD Скачать руководство пользователя страница 17

Chemtrac Systems, Inc.

Page 16

2.5

SENSOR FLUSH OPTIONS

The SCM2500XRD and SCC3500XRD are available with one of two options for
automatic sensor flushing/cleaning. The first option is the Dura-Trac with flush and is
composed of a valve mounted onto the Dura-Trac sensor, which is connected to flush
water. The second option is the SMM and is composed of a flush valve, sample
isolation valve, and chemical injection pump. The Dura-Trac with flush is recommended
for Drinking Water applications where high turbidity is often experienced. The SMM is
recommended for Waste Water applications. These options are only supplied if
specified at the time of purchase. The line of monitors offered by Chemtrac

®

can be

upgraded to include one of these two options. To upgrade to the Dura-Trac with either
options, the Dura-Trac sensor will need to be returned to the factory.

Potable water or the best quality plant water available shall be used for the flush water
supply. If potable water is used for flush water, a backflow prevention device should be
installed on the flush water line to prevent contamination of the potable water source.
The flush water needs to maintain a pressure of 35 PSI min to 80 PSI max.

2.5.1 Dura-Trac with Flush

Connect the male NPT end of the ¼’’ MNPT to ¼’’ Quick Connect Tube adapter fitting
(supplied with the unit) to the flush water supply. Connect a sufficient length of ¼’’
Teflon tubing between the flush water supply (¼’’ Quick Connect Tube adapter fitting)
and the valve’s ¼” quick connect fitting (see Figure 10 on the next page). The flush
valve’s outlet should already be connected to the probe flush assembly. The third valve
outlet (located on the bottom of the valve and pointed towards the ground) is the drain
outlet. Run this outlet to an appropriate drain using ¼’’ semi-rigid tubing. A manual
control valve should be installed on the flush water line in close proximity of the unit so

SAMPLE OUTLET
45 DEGREE ELBOW

PATENTED MADE IN U.S.A.

DURA-TRAC II

SAMPLE INLET

3/4" BARB FITTING

TM

CHEMTRAC

SYSTEMS, INC.

2" Line

4" Cup

PVC Drain

Funnel

FIGURE 8. Dura-TRAC

II

Sensor Sample Connection

«
...
15
16
17
18
19
...
»

Содержание SCC3500XRD



























































Отзывы:

Нет отзывов