Checkline TI-25DLX Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 42

Checkline TI-25DLX Скачать руководство пользователя страница 32

–31 –

7.11 Lock

The lock feature was built into the TI-25DLX for the purpose of locking the operators
out of editing any of the gauge settings, for purposes of consistency between operators.
When the lock feature is enabled, the gauge calibration functionality cannot be altered,
as well as any of the individual features in the gauge. The only keys that are always
unlocked are the power and probe zero keys, as these must remain unlocked for
measurement functionality.

The procedure to enable/disable the lock feature is outlined below:

1. With the TI-25DLX powered off, press and hold down the

key while

powering the TI-25DLX on . The lock icon will

be illuminated on the display.

2. To unlock the TI-25DLX repeat step one, but hold down the

key while

powering the TI-25DLX on.

7.12 Factory Defaults

The TI-25DLX can be reset to factory defaults at any time to restore the original gauge
settings. This should only be used if the gauge is not functioning properly, or perhaps
multiple features have been enabled and a clean start is needed.

The procedure to reset the gauge is outlined below:

1. With the TI-25DLX powered off, press and hold down the

???

and

keys

while powering the TI-25DLX on .

NOTE:

Once the measurement screen is displayed the keys can be released.

«
...
30
31
32
33
34
...
»

Содержание TI-25DLX











































Отзывы:

Нет отзывов