background image

Check Point 21400 VSX Rear Panel 

 

Check Point 21400 VSX Front

 and Rear Panel     Page 19 

 

Item  Description 

Link 

 

OFF - No Link 

 

ON (Green) - Link 

Link 

 

OFF - No Link 

 

ON (Green) - 10Mbps or 1Gbps Link 

 

ON (Amber) - 100Mbps Link 

 

Check Point 21400 VSX Rear Panel 

 

Item  Description 

2 redundant, hot-swappable AC power supplies. Each power supply connects to an 
electric outlet. 

LED indicator for power supply, one for each power supply: 

  OFF 

— power off 

  ON (Green) 

— power on. 

Main power switch. 

Power supply alarm suppression button. When a power supply fails or is not connected 
to the outlet, an alarm sounds continuously. Press here to turn off the alarm. 

Grounding plug 

5 replaceable CPU cooling fans, behind the grille. Each cooling fan operates 
independently of the others, providing redundancy in the event of failure. 

Fan grille retaining screw 

The fans are redundant pairs. They are numbered from right to left: 

1A/B

2A/B

3A/B

4A/B

5A/B

Extraction handles and retaining thumb screws for the bottom tray (that contains the 
system board) and the top tray (for an ADP Service module). There are also extraction 
handles and retaining screws on the right. 

10 

Accelerated Data Path (ADP) service module tray, behind the grille. 

 

 

Содержание 21400 VSX G-50




































Отзывы: