background image

 

 

Preface 

Purpose of this instructions 

This  paper  is  the  user  manual  of  D270  depth  sounder  of  Shanghai  Huace 

Navigation Technology   Co., LTD. 

About the instructions 

This user manual describes in detail how to install, configure and use the D270 

sounder. 

Experience requirements 

In order to better use the D270 sounder, Shanghai Huace Navigation Technology 

Co., Ltd. recommends that you read the user manual carefully before using it.If you 

are not familiar with the principle of the depth sounder, please contact us for technical 

advice and training. 

Liability exemption 

Before using this product, please read this manual carefully. The information, data 

and illustrations contained in this manual only represent the technology we currently 

know. Our company will not be responsible for any direct or indirect economic losses 

caused by users' wrong understanding or use of this product.We reserve the right to 

change  the  functions,  performance,  technical  specifications  and  manufacturing 

process  of  our  products  without  prior  notice.  For  more  information  about  our 

products, please visit our official website (www.huace.cn). 

Technology and Service 

Содержание D270

























Отзывы: