Chauvin Arnoux 2126.54 Скачать руководство пользователя страница 14

Страница: 14 / 32

Megohmmeter Models 6528/6529

3. OPERATION

3.1 Battery Installation

Place the batteries in the instrument as follows:

1. Use a Phillips screwdriver to remove the battery cover

screw on the back of the instrument (see illustration
on right).

2. Install the batteries, respecting polarity. Requires six

AA (LR6) batteries.

3. Replace the battery cover and tighten the screw.

3.2 Instrument Check

We recommend performing the following steps
when using the instrument for the first time, or
after a long period without use.

1. Start the instrument. Ensure all display segments are displayed.
2. Perform a Continuity check (§3.6). Ensure the LCD displays >42.0

Ω

with no input connected.

Then short circuit both terminals, the display should show

0Ω

3. Turn the rotary switch to

, check a known voltage (e.g., a battery) and ensure that the measured

voltage is correct.

4. Disconnect from the voltage source, and press the

TEST

button. The instrument’s battery voltage

is displayed. Ensure this is above 6.6V.

5. Turn the rotary switch to an insulation voltage setting (§3.7), and check a known resistor that

is within the measurement range for the test voltage selected.

6. When all the steps above produce expected results, you can start using the instrument.

3.3 Power Supply and Battery Life

The power supply is six 1.5V alkaline batteries (type AA or LR6). Nominal voltage is 6.6 to 9.6V. Below
6.6V the instrument will not turn on.

■

Battery life for insulation measurements:

Average battery life for insulation measurement

(according to IEC61557-2 clause 6.7) is 2000 measurements with new batteries at room
temperature (5s ON, 25s OFF).

■

Battery life for voltage and resistance measurements:

Average battery life for voltage

and resistance with new batteries at room temperature @ 400kΩ is > 300h.

■

Battery life for continuity checking:

Average battery life for continuity checking (according

to IEC 61557-4 clause 6.6) is > 6000 measurements with new batteries at room temperature
(5s ON, 25s OFF). For shorter continuity tests (0.8s ON, 10s OFF) battery life is > 40,000 tests.

■

Battery voltage:

To check the battery voltage, press and hold the

TEST

button with the switch

set to the

position.

Содержание 2126.54

































Результаты поиска

Содержание 2126.54

Отзывы:

Похожие инструкции для 2126.54

Бренды по названию

Популярные бренды

Chauvin Arnoux 2126.54, Руководство пользователя

Результаты поиска

Содержание 2126.54

Отзывы:

Похожие инструкции для 2126.54

Бренды по названию

Популярные бренды