background image

 

Scorpion™ Storm RGX User Manual 

8/18/2011 

Safety Instructions 

 

 

 

 
Please read the following notes carefully because they include important safety 
information about the installation, usage, and maintenance of this product. 

 

 

 

  Keep this User Manual for future consultation. If you sell this product to another user, 

be sure that they also receive this document. 

  Always make sure that the voltage of the outlet to which you are connecting this 

product is within the range stated on the decal or rear panel of the product. 

  This product is for indoor use only! To prevent risk of fire or shock, do not expose this 

product to rain or moisture. 

  Make sure there are no flammable materials close to the unit while operating. 

  Always install this product in a location with adequate ventilation, at least 20 in (50 cm) 

from adjacent surfaces. Be sure that no ventilation slots are blocked. 

  Always disconnect this product from the power source before cleaning it or replacing 

fuse. 

  Make sure to replace the fuse with another of the same type and rating. 

  If mounting it overhead, always secure this product to a fastening device using a 

safety chain. 

  The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate this product 

at higher temperatures.  

  In the event of a serious operating problem, stop using the unit immediately. Never try 

to repair the unit. Repairs carried out by unskilled people can lead to damage or 
malfunction. Please contact the nearest authorized technical assistance center. 

  Never connect this product to a dimmer pack. 

  Make sure the power cord is not crimped or damaged. 

  Never disconnect the power cord by pulling or tugging on the cord. 

  Never carry a product from the power cord or any moving part. Always use the 

hanging/mounting bracket or the handles. 

  Always avoid direct eye exposure to the light source when this product is on. 

  Lasers can be hazardous and have unique safety considerations. Permanent eye 

injury and blindness is possible if lasers are used incorrectly. Pay close attention to 
each safety REMARK and WARNING statement in this user manual. Read all 
instructions carefully BEFORE operating this device. 

 

 

 

 

Avoid direct eye contact with laser light. Never intentionally expose your eyes or 

others to direct laser light. 

 

This laser product can potentially cause instant eye injury or blindness if laser 

light directly strikes the eyes. 

 

It is illegal and dangerous to shine this laser into audience areas, where the 

audience or other personnel could get direct laser beams or bright reflections 
into their eyes. 

 

It is a US Federal offense to shine any laser at aircraft. 

 

Use of controls or adjustments or performance of procedures other than those 

specified herein may result in hazardous radiation exposure. 

 

There are no user serviceable parts inside the unit. Do not open the housing or 

attempt any repairs yourself. In the unlikely event your unit may require service, 
please contact the dealer nearest to you. 

 

Avoid direct eye contact with laser light. Never intentionally expose your eyes or 

others to direct laser light. 

 

Содержание Scorpion Storm RGX



















Отзывы: