background image

 

Scorpion™ Storm FXGB User Manual 

10 

Rev. 4 

 The fuse is located 
inside this 
compartment. 
Remove using a flat 
head screwdriver. 

Hanging Clamp 

Note! 
Clamp is sold separately. 

3.

 

S

ETUP

 

AC Power 

This fixture has an auto-switching power supply that can accommodate a wide range of input 
voltages. The only thing necessary to do before powering on the unit is to make sure the line 
voltage you are applying is within the range of accepted voltages. This fixture will accommodate 
100~240 VAC, 50/60 Hz. 

 

 

Always connect the product to a switched circuit. Never connect the product to a rheostat 
(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used only as a 0 to 
100% switch. 

Fuse Replacement 

With a flat head screwdriver, wedge the fuse holder 
out of its housing. Remove the damaged fuse from 
its holder and replace with exact same type fuse. 
Insert the fuse holder back in its place and 
reconnect

 

power.

  

 

Disconnect the power cord before replacing a fuse and always replace with the same type fuse. 

Mounting 

Orientation 

This fixture may be mounted in any safe position, provided there is adequate room for ventilation. 

Rigging  

It is important never to obstruct the fan or vents pathway. Mount the 
fixture using, a suitable C or O type clamp. Adjust the angle of the 
fixture by loosening both knobs and tilting the fixture. After finding the desired 
position, retighten both knobs. 

 

When selecting installation location, take into consideration 
access and routine maintenance.  

 

Safety cables must always be used.  

 

Never mount in places where the fixture will be exposed to 
rain, high humidity, extreme temperature changes or 
restricted ventilation. 

Proper Usage 

 

 

 

This  product  is  for overhead mounting only.  For safety purposes, CHAUVET® 
recommends mounting your lighting effect products on steady elevated platforms or 
sturdy overhead supports using suitable hanging clamps. In all cases, you must use 
safety cables.  You can obtain appropriate mounting hardware from your lighting 
vendor.  

International laser safety regulations require that laser products must be operated in 
the fashion illustrated below, with a minimum of 3 meters (9.8 ft) of vertical separation 
between the floor and the lowest laser light vertically. Additionally, 3 meters of 
horizontal separation is required between laser light and audience or other public 
spaces. 

Содержание Scorpion Storm FXGB

















Отзывы: