Charnwood W650 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 21

Charnwood W650 Скачать руководство пользователя страница 4

4

Specification

Main table size

480(w) x 720(d) mm

Rear table size

480(w) x 280 (d) mm

Side Table size

270(w) x 720(d) mm

Table height

830mm

Motor (induction)

2200W (3hp), 240v single phase

Blade diameter and bore

254mm (10”) x 30mm

Blade rotation speed (no load)

4000 rpm

Maximum depth of cut at 90

80mm

Maximum depth of cut at 45

56mm

Maximum ripping width using fence

610 mm (24”)

Maximum cross cutting width

550mm/700mm (fence front/rear of table)

Dust extractor hose connection

100mm

Overall Dimensions (WxDxH)

1430mm x 1340mm x 1130mm

Weight Gross/Nett

150kg/125 kg

Unpacking

The saw is shipped in two parts - a crate and a box.
Open both and carefully unpack all of the contents.

Remove the greased paper from the table & sliding
carriage and clean with WD40 or similar.

Using a 16mm spanner, under the wooden pallet,
remove the two bolts which secure the machine
base to the pallet.

«
...
2
3
4
5
6
...
»

Содержание W650






















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды