background image

REV 42436-20130424  

10

42436

 

ENGLISH

OPERATION

Grounding

The generator system ground connects the frame to the 
ground terminals on the power panel.

 

– The generator (stator winding) is isolated from the 

frame and from the AC receptacle ground pin. 

 

– Electrical devices that require a grounded receptacle 

pin connection may not function properly.

Surge Protection

Electronic devices, including computers and many 
programmable appliances use components that are 
designed to operate within a narrow voltage range and 
may be affected by momentary voltage fluctuations. 
While there is no way to prevent voltage fluctuations, you 
can take steps to protect sensitive electronic equipment. 
1.  Install UL1449, CSA-listed, plug-in surge suppressors 

on the outlets feeding your sensitive equipment.  
Surge suppressors come in single- or multi-outlet 
styles. They’re designed to protect against virtually 
all short-duration voltage fluctuations.

Voltage fluctuation may impair the proper 
functioning of sensitive electronic equipment.

CAUTION

If the engine starts but does not run make certain 
that the generator is on a flat, level surface. The 
engine is equipped with a low oil sensor that will 
prevent the engine from running when the oil level 
falls below a critical threshold.

NOTE

Starting the Engine

1.  Make certain the generator is on a flat, level surface.
2.  Disconnect all electrical loads from the generator. 

Never start or stop the generator with electrical 
devices plugged in or turned on.

3.  Turn the Fuel Valve to the “ON” position.
4.  Flip the engine switch to the “ON” position.
5.  Move the choke lever to the “CHOKE” position.
6.  Pull the starter cord slowly until resistance is felt and 

then pull rapidly

7.  Do not over-choke. As as soon as engine starts, move 

the choke lever to the “RUN” position.

Keep choke lever in “Choke” position for only 1 
pull of the recoil starter. After first pull, move choke 
lever to the “Run” position for up to the next 3 
pulls of the recoil starter. Too much choke leads to 
sparkplug fouling/engine flooding due to the lack of 
incoming air. This will cause the engine not to start.

NOTE

Generator Location

NEVER operate the generator inside any building, 
including garages, basements, crawlspaces and sheds, 
enclosure or compartment, including the generator 
compartment of a recreational vehicle. Please consult 
your local authority. In some areas, generators must 
be registered with the local utility. Generators used at 
construction sites may be subject to additional rules and 
regulations. Generators should be on a flat, level surface 
at all times. (Even while not in operation) Generators 
must have at least five feet of clearance from all 
combustible material. In addition to clearance from all 
combustible material, generators must also have at least 
three feet of clearance on all sides to allow for adequate 
cooling, maintenance and servicing. Generators should 
never be started or operated in the back of a SUV, 
camper, trailer, in the bed of a truck (regular, flat or 
otherwise), under staircases/stairwells, next to walls or 
buildings, or in any other location that will not allow for 
adequate cooling of the generator and/or the muffler. 
DO NOT contain generators during operation. Allow 
generators to properly cool before transport or storage.
Place the generator in a well-ventilated area. DO NOT 
place the generator near vents or intakes where exhaust 
fumes could be drawn into occupied or confined 
spaces. Carefully consider wind and air currents when 
positioning generator.
Failure to follow proper safety precautions may void 
manufacturer’s warranty.

Do not operate or store the generator in rain, snow, or 
wet weather.

Using a generator or electrical appliance in wet 
conditions, such as rain or snow, or near a pool or 
sprinkler system, or when your hands are wet, could 
result in electrocution.

WARNING

WARNING

During operation the muffler and exhaust fumes 
produced will become hot. If adequate cooling and 
breathing space are not supplied, or if the generator 
is blocked or contained, temperatures can become 
extremely heated and may lead to fire.

Содержание 42432





























Отзывы: