Champion 40903 Скачать руководство пользователя страница 9

Страница: 9 / 28

STEP 3.

THROWING ARM ASSEMBLY (FIG-7).
Line-up three holes in Throwing Arm (A) with

three holes in Arm Support. Insert three 10MM

X 20MM Hex Head Bolts (N-5) from bottom

through Throwing Arm Support and Throwing

Arm. Add 10MM Flange Nut (N-10) and tighten

securely using wrenches.

STEP 4.

FLIGHT CONTROL RAIL ASSEMBLY (FIG-7).
Line-up threaded holes in Flight Control Rail

(G) with top holes in edge of Throwing Arm

(A). Attach Flight Control Rail with three Round

Head Screws (N-7). Do not fully tighten screws

until the Target Clip is installed (Step 5)

NOTE: It is normal for these screws to be

somewhat difficult to turn.

STEP 5.

TARGET CLIP ASSEMBLY (FIG-8).

After attaching the Flight Control Rail in the

previous step, slide the Target Clip (I) between

the Flight Control Rail (G) and the Throwing

Arm (A) and tighten the three screws (N-7).

STEP 6.

MAINSPRING ASSEMBLY (FIG-9)
Drop Hex Bolt (N-8), threaded end first, into Mainspring (H) through largest

opening so that threaded end comes out of opposite tapered end. Make

sure Throwing Arm (A) is pointing forward (12 o’clock position). Connect

hook end of Mainspring (H) through hole in Swivel Yoke. Put threaded end

of Hex Bolt (N-8) through hole in Rear Bracket. Add the Nylon Shoulder

Washer (N-14), 10MM Flat Washer (N-9), and 10MM Hex Nut (N-11) and

finger tighten. Adjustment of Mainspring tension for throwing targets will

be done later.

TRAP ASSEMBLY INSTRUCTIONS (continued)

Throwing Arm (A)

Flight Control

Rail (G)

Sheet Metal Screws (N-‐7)

3/8-‐16 Flange Nuts (N-‐10)

Arm Support

3/8-‐16 x 7/8” Hex Bolts (N-‐

FIGURE 7

FIGURE 8

Target Clip (I)

Throwing Arm (A)

3/8-‐16 x 4” lg.

Hex Bolt (N-‐8)

Nylon

Shoulder

Washer

(N-‐14)

3/8” Flat

Washer (N-‐

3/8-‐16

Hex Nut

(N-‐11)

Swivel Yoke

Mainspring

Assembly (H)

Cotter Pin

Washer

Rear Bracket

Trap Arm Faces Forward

FIGURE 9

FIGURE 7

FIGURE 8

FIGURE 9

Round Head Machine Screws (N-7)

10MM Flange Nuts (N-10)

3/8” Flat Washer

(N-9)

10MM X 20MM Hex Bolts (N-5)

10MM X 125MM

Lg, Hex Bolt (N-8)

10MM Flat

Washer (N-9)

10MM

Hex Nut

(N-11)

Содержание 40903





























Результаты поиска

Содержание 40903

Отзывы:

Champion 40903, Руководство владельца/оператора, Страница: 9 / 28

Результаты поиска

Содержание 40903

Отзывы: