background image

 

Champion Power Equipment, Inc. (CPE),  

United States Environment Protection Agency (U.S. EPA) 

Emission Control System Warranty  

 
Your Champion Power Equipment (CPE) engine complies with U.S. EPA emission regulations.  
 

YOUR WARRANTY RIGHTS AND OBLIGATIONS: 

 
The US EPA AND CPE are pleased to explain the Federal Emission Control Systems Warranty on your 2016 small 
off-road engine and engine powered equipment. New engines and equipment must be designed, built and 
equipped, at the time of sale, to meet U.S. EPA regulations for small non-road engines. CPE warrants the emission 
control system on your small off-road engine and equipment for the period of time listed below, provided there has 
been no abuse, neglect, unapproved modification, or improper maintenance of your equipment. 
 
Your emission control system may include parts such as the carburetor, fuel-injection system, the ignition system, 
catalytic converter and fuel lines. Also included may be hoses, belts, connectors and other emission related 
assemblies. Where a warrantable condition exits, CPE will repair your small off-road engine at no cost to you 
including diagnosis, parts and labor. 
 

MANUFACTURER’S EMISSION CONTROL SYSTEM WARRANTY COVERAGE:

 

 
 This  emission  control  system  is  warranted  for  two  years,  subject  to  provisions  set  forth  below.  If,  during  the 
warranty  period,  emission  related  part  on  your  engine  is  defective  in  materials  or  workmanship,  the  part  will  be 
repaired or replaced by CPE. 
 

OWNER WARRANTY RESPONSIBILITIES: 

As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in 
your Owner’s Manual. CPE recommends that you retain all your receipts covering maintenance on your small off-
road  engine,  but  CPE  cannot  deny  warranty  solely  for  the  lack  of  receipts  or  for  your  failure  to  ensure  the 
performance of all scheduled maintenance. 
 
As the small off-road engine owner, you should however be aware that CPE may deny you warranty coverage if 
your small, off-road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved 
modifications.  
 
You  are  responsible  for  presenting  your  small  off-road  engine  to  an  Authorized  CPE  service  outlet  or  alternate 
service outlet as described in (3)(f.) below, CPE dealer or CPE, Santa Fe Springs, Ca. as soon as a problem exists. 
The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.  
 
If you have any questions regarding your warranty rights and responsibilities, you should contact: 
 

Champion Power Equipment, Inc. 

Customer Service 
12039 Smith Ave. 

Santa Fe Springs, CA 90670 

1-877-338-0999 

[email protected] 

Содержание 92251-1
































Отзывы: