background image

12

92251-1

 

ENGLISH

OPERATION

Before Each Use Inspect the Log Splitter

1.  Check the hydraulic oil level and visually inspect all 

hoses, attachments and cylinder for loose fittings, 
leaks, cracks, fraying or other damage.

2.  DO NOT operate the log splitter if there is any 

indication of damage.

3.  Inspect the engine and make sure the oil level is 

correct before operating. If the engine is equipped 
with a spark arrestor, clean and inspect it regularly 
(follow spark arrestor maintenance schedule).

4.  The tires need to be fully inflated and in good repair. 

Reference the tire sidewall for recommended tire 
pressure.

Towing Log Splitter Safety

1.  Always check local and state regulations regarding the 

requirements for towing, licensing and lights.

2.  Before towing make sure the log splitter is correctly 

and securely attached to the vehicle and the safety 
chains attached with enough slack to allow for turning.

3.  Never exceed the max. travel speed of 45 mph         

(72 kph). Towing the log splitter at speeds greater 
than 45 mph (72 kph) could result in serious injury or 
death. Always adjust your towing speed according to the 
terrain and conditions.

4.  Always disconnect the log splitter from the towing 

vehicle before operating.

Log Splitter Location

This log splitter must have at least seven feet of 
clearance from combustible material. Leave at least 
three feet of clearance on all sides of the log splitter to 
allow for adequate cooling, maintenance and servicing. 
DO NOT place the log splitter near vents or intakes 
where engine exhaust fumes could be drawn into 
occupied or confined spaces.

 Always operate the log 

splitter outdoors.
The log splitter needs to be on a dry level surface with 
good footing. DO NOT work on mud, ice, tall grass, 
brush or snow.
Only operate log splitter from work zone shown below.

DO NOT over inflate tires. Serious injury can result 
if tires explode. 
DO NOT tow the log splitter if the tires are worn or 
will not hold air. 
DO NOT exceed the maximum 45 MPH (72 KPH)
towing speed.

WARNING

Vertical Operating

Position

Work Zone

Horizontal Operating

Position

Wo

rk

   

  

 

Zo

ne

Log Splitter Location Cont’d.

Содержание 92251-1
































Отзывы: