background image

100680 - 27 iN. 2-STAgE SNOwbLOwER

OPERATiON

20

OPERATiON

 

wARNiNg

Never use the snowblower without first reading and 
understanding the operating instructions, warnings and 
instruction labels located on the machine.

before Operation

 

Check the General Condition.

 

Look around and underneath the engine for signs of oil or 
gasoline leaks.

 

Remove any excessive dirt or debris, especially around the 
muffler and recoil starter.

 

Look for signs of damage.

 

Check that all shields and covers are in place, and all nuts, 
bolts, and screws are tightened.

Check the Engine

1.  There is no fuel or oil in the engine. Fill with fuel and add  

0W-30 prior to first use.

2.  Check the fuel level (see 

Add Fuel

 under 

Assembly

 section).

3.  Check the oil level (see 

Add Engine Oil

 under 

Assembly

 

section).

 

wARNiNg

Always check the engine oil level before operation. Using the 
snowblower without oil can seriously damage the engine and 
void your warranty. The machine must stand on level ground 
when checking.

Engine key and throttle lever plastic piece need to be attached 
before first use. These parts may be attached to the recoil 
starter grip. Please remove the key and throttle lever from the 
recoil starter grip and attach/install properly.

 

wARNiNg

Always wear eye protection with side shields marked to 
comply with ANSI Z87.1. Failure to do so could result in objects 
being thrown into your eyes and other possible serious injuries.

Starting the Engine

1.  Make sure the engine key (safety lock out) is inserted into the 

key hole.

2.  To start a warm engine: (Fig. 14).

2a. Move the fuel valve lever to the ON position.

2b. Move the choke lever to the RUN position.

2c. Move the throttle lever to full speed.

2d. Do not prime.

CHOKE

FULL SPEED

FUEL OFF

FUEL ON

RUN

Figure 14

3.  To start a cold engine: (Fig. 15).

3a. Move the fuel valve lever to the ON position.

3b. Move the choke lever to the CHOKE position.

3c. Move the throttle lever to full speed.

3d. Prime 3-5 times.

CHOKE

FULL SPEED

FUEL OFF

FUEL ON

RUN

Figure 15

Содержание 100680







































Отзывы: