100679 - 24 iN. 2-STAgE SNOwbLOwER
iMPORTANT SAfETY iNSTRUCTiONS
6
Operation
1. Do not put hands or feet near or under rotating parts. Keep
clear of the discharge opening at all times.
2. Exercise extreme caution when operating on or crossing
gravel drives, walks, or roads. Stay alert for hidden hazards
or traffic.
3. In the event of striking a foreign object, stop the engine,
remove the spark plug, thoroughly inspect the snowblower
for any damage, and repair the damage before restarting and
operating the snowblower.
4. If the snowblower should start to vibrate abnormally, stop
the engine and check immediately for the cause. Vibration is
generally a warning of trouble. Vibration typically indicates a
mechanical problem has occurred.
5. Always stop the engine whenever you leave the operating
position, before unclogging the auger housing or discharge
guide, and when making any repairs, adjustments, or
inspections.
6. Before cleaning, inspecting or repairing any parts of the
snowblower, always ensure the auger has stopped moving.
Disconnect the spark plug wire and keep it away from the
plug to prevent accidental starting.
7. Before leaving the machine unattended, disengage all control
levers, stop the engine and remove the safety key.
8. Do not run the engine indoors. Exhaust fumes are dangerous
and can kill you.
9. Do not clear snow across the face of slopes. Exercise extreme
caution when changing direction on slopes. Never attempt to
clear steep slopes.
10. Never operate the snowblower without proper guards, plates
or other safety protective devices in place.
11. Never operate the snowblower near glass enclosures,
automobiles, window wells, etc., without proper adjustment
of the snow discharge angle. Keep children and pets away.
12. Do not overload the machine capacity by attempting to clear
snow at too fast a rate.
13. Never operate the machine at high transport speeds on
slippery surfaces. Use care when reversing.
14. Never direct discharge at bystanders or allow anyone in front
of the unit.
15. Disengage power to the impeller when snowblower is
transported or not in use.
16. Use only attachments and accessories approved by the
manufacturer of snowblower (such as wheel weights,
counterweights, cabs, etc.).
17. Never operate the snowblower without good visibility or light.
Always be sure of your footing, and keep a firm hold on the
handles. Walk; never run.
18. Keep all nuts, bolts and screws tight to be sure the equipment
is in safe working condition prior to operation.
19. Replace worn or damaged parts for safety; Use only genuine
replacement parts and accessories.
20. This snowblower is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge of
mechanical equipment.
21. Be careful while working on the machine or clearing a
blockage in the auger or impeller to ensure that fingers and
hands do not become crushed or cut.
22. Do not touch hot engine components like the muffler, muffler
guard or engine block during operation of the snowblower as
they will cause burns.
23. Should the unit stop discharging snow for any reason,
release the controls to stop the auger and the engine before
inspecting for any lodged items or damaged parts in the
auger housing.
Clearing a Clogged Discharge Chute
DANgER
DO NOT use your hands to clean out the discharge chute.
To clear the chute:
1. SHUT THE ENGINE OFF!
2. Wait 10 seconds to be sure the auger blades have stopped
rotating.
3. Always use the provided clean-out tool to clear out the
discharge chute.
Maintenance and Storage
1. Check shear bolts, engine mounted bolts, etc., at frequent
intervals for proper tightness to ensure the equipment is in
safe, working condition.
2. Never store the machine with gasoline in the fuel tank inside
a building where automatic ignition sources are present such
as hot water heaters, space heaters, clothes dryers or any
open flame sources.
3. Run the snowblower for one minute to clear out packed snow
and ice to prevent freeze-up prior to storage.
4. Always allow the engine to cool before storing in any
enclosure.
5. Always refer to Operator’s Manual for important details when
the snowblower is to be stored for extended periods of time.
6. Maintain or replace safety and instructions labels, as
necessary.
