Champion Global Power Equipment 200987 Скачать руководство пользователя страница 32

Страница: 32 / 42

200987 - 4500W WIRELESS REMOTE START INVERTER GENERATOR

MAINTENANCE



NOTICE

Once oil has been added, a visual check should show oil
about 1-2 threads from running out of the fill hole. If using the
dipstick to check oil level, DO NOT screw in the dipstick while
checking.

Cleaning and Adjusting the Spark Plug

1. Remove the non recoil side maintenance cover by removing

the two screws with a phillips head screw driver
(included).

2. Remove the spark plug cable from the spark plug.

3. Use a spark plug socket tool (included), or a

13/16 in. (21 mm) socket (not included) to remove the plug.

4. Inspect the electrode on the plug. It must be clean and not

worn to produce the spark required for ignition.

5. Make certain the spark plug gap is

0.028-0.031 in. (0.7-0.8 mm).

SPARK PLUG GAP

6. Refer to the spark plug types in

Specifications

when replacing

the plug.

7. Firmly re-install the plug.

8. Attach the spark plug cable to the spark plug.

9. Reinstall the maintenance cover.

Cleaning the Air filter

1. Remove the non recoil side maintenance cover by removing

the two screws with a phillips head screw driver
(included).

2. Locate the air filter plastic cover and remove by pinching the

clips together and pulling the cover off.

3. Remove the foam element.

4. Wash in liquid detergent and water. Squeeze thoroughly dry in

a clean cloth.

5. Saturate in clean engine oil.

6. Squeeze in a clean, absorbent cloth to remove all excess oil.

7. Place the filter in the assembly.

8. Reattach the air filter cover.

9. Reinstall the maintenance cover and tighten the cover screw

securely.

Cleaning the Spark Arrestor

1. Allow the engine to cool completely before servicing the spark

arrestor.

2. Remove the two screws holding the cover plate which retains

the spark arrestor to the muffler.

3. Remove the spark arrestor and spark arrestor screen.

4. Carefully remove the carbon deposits from the spark arrestor

and spark arrestor screen with a wire brush.

5. Replace the spark arrestor and spark arrestor screen if it they

damaged.

Содержание 200987











































Результаты поиска

Содержание 200987

Отзывы:

Бренды по названию

Популярные бренды

Champion Global Power Equipment 200987, Руководство оператора

Результаты поиска

Содержание 200987

Отзывы:

Бренды по названию

Популярные бренды