background image

Assembly Step 2

Install the Trolley on the T-rail

9

• As a temporary stop, insert a screwdriver into the

hole in the front end of the T-rail.

• Slide the trolley assembly along the rail to the

screwdriver stop.

If trolley hits against any nuts on the T-rail, the
bolts and nuts were attached from the wrong 
side and must be repositioned. Review Step 1.

• Insert a 5/16"-18x7/8" hex screw into the trolley

stop hole in the T-rail as shown. Tighten securely
with a 5/16" lock washer and nut. This screw limits
trolley travel in the DOWN direction.

Trolley

Temporary Stop

Screwdriver

Hex Screw

5/16"-18x7/8"

Trolley

Stop Hole

Lock Washer

5/16"

Nut 

5/16"-18

Assembly Step 3

Faster the T-rail to the Opener

• Place the opener on packing material to protect

the cover. For convenience, put a support under
the belt pulley bracket.

• Remove the (2) 5/16"-18x1/2" washered screws

mounted in the top of the opener.

• Align the holes in the back section of the T-rail with

the holes in the opener.

• Fasten the rail with the (2) washered screws

previously removed. Tighten securely.

Remember to use only these screws! Any other
screws will cause serious damage to the opener.

• Insert a 5/16"-18x7/8" hex screw into the cover

protection bolt hole in the T-rail as shown. Tighten
securely with a 5/16" lock washer and nut.

NOTE:  This screw prevents trolley over-travel.
Keep a 2" minimum between the trolley and this
screw when adjusting travel limits (see page 28).

Washered Screw

5/16"-18x1/2"

USE ONLY THIS

TYPE AND SIZE 

SCREW

T-Rail

(Back Section)

Cover Protection

BoltHole

Nut

5/16"-18

Hex Screw

5/16"-18x7/8"

Lock Washer

5/16"

To fasten rail, use only those screws mounted
in the top of the opener. Any other screws will
cause serious damage to the opener.

Nut

5/16"-18

Lock Washer

5/16"

Hex Screw

5/16"-18x7/8"

Hardware Shown Actual Size

CAUTION

CAUTION

Содержание Security+ 9200C-2K









































Отзывы: