manualshive.com logo in svg

Chamberlain Secure Home SH-9132AU, Инструкция по установке и эксплуатации, Страница: 1 / 8

Поделиться
Скачать
Chamberlain Secure Home SH-9132AU Скачать руководство пользователя страница 1

FEATURES

• Automatically comes on when motion is de-

tected.

• Automatically turns light off.

• Photocell keeps the light off during daylight 

hours.

UNPACKING

Be sure to remove all contents from packaging 

and verify all items are present before assembling 

this light fixture. This package includes the fol-

lowing items:

• Coach Light

• Mounting Bracket (Mounting Bracket Screws 

Are Not Included - Use 4mm dia. (8G) x 30 mm 

Screws)

• Owner’s Manual

• Some  models  will  include  an  additional  tail 

assembly

REQUIREMENTS

• The light control requires 230 volts AC.

• If you want to use Manual Mode, the control 

must be wired through a switch.

• It is illegal for persons other than a licensed 

electrician or person authorized by legislation 

to work on fixed wiring or other electrical 

installations.

Before installation, record the model num-

ber listed inside the fixture. Attach receipt 

in case of possible warranty issues.
Model Number:

© 2011 The Chamberlain Group, Inc 

201101-01A

Motion Sensing

Coach Light

Coach Light*

*Note:

 Illustrations are for reference only and may 

be different from actual product

Installation and Operating Instructions

Models: SH-9132AU, SH-9133AU, 

SH-9138AU, SH-9144AU, and

SH-9150AU

®

TM

Содержание Secure Home SH-9132AU









Отзывы:

Нет отзывов