background image

2

TABLE OF CONTENTS

When you see these Safety Symbols and Signal Words 
on the following pages, they will alert you to the possibility 
of 

serious injury or death

 if you do not comply with the 

warnings that accompany them. The hazard may come 
from something mechanical or from electric shock. Read 
the warnings carefully.

When you see this Signal Word on the following pages, it 
will alert you to the possibility of damage to your garage 
door and/or the garage door opener if you do not comply 
with the cautionary statements that accompany it. Read 
them carefully.

INTRODUCTION

Safety Symbol 
and Signal Word Review

This garage door opener has been designed and tested to offer safe service provided it is installed, operated, 
maintained and tested in strict accordance with the instructions and warnings contained in this manual.

Mechanical

Electrical

Introduction 2-7

Safety symbol and signal word review ....................... 2

Preparing your garage door ....................................... 3

Tools needed .............................................................. 3

Planning  ................................................................. 4-5

Carton inventory ......................................................... 6

Hardware inventory .................................................... 7

Assembly  

8-11

Assemble the rail and install the trolley ...................... 8

Fasten the rail to the motor unit and
install the idler pulley .................................................. 9

Install the chain/cable ............................................... 10

Tighten the chain .......................................................11

Installation  

11-26

Installation safety instructions ...................................11

Determine the header bracket location .................... 12

Install the header bracket ......................................... 13

Attach the rail to the header bracket ........................ 14

Position the opener .................................................. 15

Hang the opener ....................................................... 16

Install the door control .............................................. 17

Install the lights ......................................................... 18

Attach the emergency release rope and handle ...... 18

Electrical requirements ............................................. 19

Install The Protector System

®

.............................. 20-22

Fasten the door bracket ...................................... 23-24

Connect the door arm to the trolley ..................... 25-26

Adjustment 27-29

Adjust the travel limits .............................................. 27

Adjust the force ........................................................ 28

Test the safety reversal system ................................ 29

Test The Protector System

®

 ..................................... 29

Operation   

30-34

Operation safety instructions .................................... 30

Using your garage door opener ............................... 30

Using the wall-mounted door control ........................ 31

To open the door manually ....................................... 31

Care of your garage door opener ............................. 32

Having a problem? ................................................... 33

Diagnostic chart ........................................................ 34

Programming 35-36

To add or reprogram a hand-held remote control .... 35

To erase all codes .................................................... 35

3-Button remotes ...................................................... 35

To add, reprogram or change 
a Keyless Entry PIN ................................................. 36

Repair Parts   

37-38

Rail assembly parts .................................................. 37

Installation parts ....................................................... 37

Motor unit assembly parts ........................................ 38

Accessories 39

Repair Parts and Service 

40

Warranty 40

Содержание Power Drive Security+ 248735S









































Отзывы: