ADJUSTMENT SECTION
SETTING THE LIMITS
Travel limits regulate the points at which the door will stop
when moving up or down. Follow the steps below to set the lim-
its.
To program the travel limits:
1. Press and hold the black button (1) until the yellow indicator light
(3) starts flashing slowly and then release.
2. Push and hold the black button (1) until the door reaches the
desired open position. Adjust the position of the door by using the
black (1) and orange (2) buttons. Black moves the door UP,
orange moves the door DOWN.
3. Push the programmed remote control (4) or push bar on the door
control that was shipped with your opener. This sets the full UP
(open) position. The door will travel to the floor and reverse back
to the UP (open) position. The opener has learned its travel limits.
Check to be sure the door is high enough for your vehicle.
Adjust if necessary.
4. The indicator light (3) will stop flashing when the limits have been
learned.
If the door stops or reverses before it reaches the floor repeat
steps 1-3 immediately. If this does not set the limits, proceed to
#15 of the Having a Problem? section and follow the instruc-
tions for setting the limits manually.
SETTING THE FORCE
The force, as measured on the closing edge of the door, should
not exceed 400N (40kg). If the closing force is measured to
more than 400N, the Protector System must be installed See
step 29.
The force setting regulates the amount of power required to
open and close the door.
1. Locate the orange button (2).
2. Push the orange button (2) twice to enter unit into Force
Adjustment Mode. The LED (3) (indicator light) will flash quickly.
3. Push the programmed remote control (4) or push bar on the door
control that was shipped with your opener. The door will travel to
the DOWN (close) position. Push the remote control (4) again,
the door will travel to the UP (open) position.
The LED (3) (indicator light) will stop flashing when the force has
been learned.
The door must travel through a complete cycle, UP and DOWN, in
order for the force to be set properly. If the unit cannot open and
close your door fully, inspect your door to insure that it is balanced
properly and is not sticking or binding.
The force MUST be learned in order to properly complete the
setting of the limits.
26
27
TEST THE SAFETY REVERSE SYSTEM
The safety reverse system test is important. Garage door must
reverse on contact with a 40mm obstacle laid flat on the floor.
Failure to properly adjust opener may result in serious personal
injury from a closing garage door. Repeat test once a month
and adjust as needed.
Procedure:
Place a 40mm obstacle (1) laid flat on the floor under
the garage door. Operate the door in the
down
direction. The door
must reverse on the obstruction. If the door
stops
on the obstruc-
tion, remove obstruction and repeat
Setting the Limits step 26.
Repeat test.
When the door reverses on the 40mm obstacle, remove the obstruc-
tion and run the opener through a complete travel cycle. Door
must
not
reverse in closed position. If it does, repeat
Setting the Limits
and Force steps 26 and 27
and repeat safety reverse test.
Place 20kg at the center of the door and ensure that the door will not
move up more than 500mm.
28
INSTALL THE PROTECTOR SYSTEM™
(See accessories)
Install this accessory for all installations on
Canopy doors, One-Piece Door with Horizontal and Vertical Track
, doors over 2.5m and when the
closing force as measured on the bottom of the door is over 400N
(40kg).
After opener has been installed and adjusted,
The Protector
System™
accessory can be installed. Instructions are included with
this accessory.
The Protector System™ provides an additional measure of safety
against a small child being caught under a garage door.
It uses an invisible beam which, when broken by an obstruction, caus-
es a closing door to open and prevents an open door from closing and
is
strongly recommended for homeowners with young children.
Note:
The opener will automatically detect the protector system when it
is installed. The opener will not close unless the sensors are aligned.
SPECIAL FEATURES
1.
Door within a door connection
Locate auxiliary quick connect terminals. Insert bell wire into quick
connect terminals 1 and 2.
2.
Flashing light connection
The flashing light can be installed anywhere. Connect light leads
to quick connect terminals 1 and 2. Terminal 2 is ground.
3.
Timer to close function
can be enabled by turning the dial to the
required time. If the protector system is installed the timer to close
should be set after the protector system is installed.
29
30
ACCESSORIES
(1) Model 94330E
Single-Function Remote Control
(2) Model 94333E
3-Function Remote Control
(3) Model 94335E
3-Function Mini Remote Control
(4) Model 94334E
4-Function Mini Remote Control
(5) Model 128LM
Wireless Wall Control
(6) Model 9747E
Keyless Entry System
(7) Model 78LM
Multi-Function Door Control Panel
(8) Model 75E
Lighted Door Control Button
(9) Model 98LM
Motion Detector Wall Control
(10) Model 760E
Outside Keylock
(11) Model 1702E
Outside Quick Release
(12) Model 770E
The Protector System™
(13) Model FLA230
Flashing Light Kit
(14) Model 1703E
The Chamberlain Arm™
(15) Model 16200LM
Door in Door Switch
(16) Model MDL100LM
Mechanical Door Latch Kit
(17) Model EQL01
Door Handle Quick Release 2,5m
Model EQL02
Door Handle Quick Release 4,0m
(18) Model 9-13-1
Door Reinforcement Bracket
WIRING INSTRUCTIONS FOR ACCESSORIES
Outside Keylock –
To opener terminals:
Red-1 and White-2
Protector System™ –
To opener terminals:
White-3 and Grey-4
Door Control Panel –
To opener terminals:
Red-1 and White-2
31
REPLACEMENT PARTS
32
33
5-en
