12. Opener strains:
Door may be unbalanced or springs are broken. Close door and use
manual release rope and handle to disconnect trolley. Open and close
door manually. A properly balanced door will stay in any point of travel
while being supported entirely by its springs. If it does not, call for pro-
fessional garage door service to correct the problem.
13. Opener motor hums briefly, then won't work:
• Garage door springs are broken. SEE ABOVE.
• If problem occurs on first operation of opener, door is locked. Disable
door lock.
Repeat safety reverse test after adjustment is complete.
14. Opener won't activate due to power failure:
• Pull manual release rope and handle down to disconnect trolley. Door
can be opened and closed manually. When the power is restored, pull
the manual release handle down and toward opener. The next time the
opener is activated, the trolley will reconnect.
• The Outside Quick Release accessory (if fitted) disconnects the trolley
from outside the garage in case of power failure.
15. Setting the limits manually:
1. Press and hold the black button until the yellow indicator light starts
flashing slowly then release.
2. Adjust the position of the door by using the black and orange but-
tons. Black moves the door UP (open) and orange moves the door
DOWN (close).
Check to be sure the door opens high enough for your vehicle.
3. Push the remote control or door control. This sets the UP (open) limit
and begins closing the door.
Immediately press either the orange
or the black button.
The door will stop.
Adjust the desired DOWN (close) limit position using the black and
orange buttons. Check to be sure the door is fully closed without
applying excessive pressure on the rail (rail should not bow upwards
and the chain/belt should not sag or droop below the rail). Push the
remote control or door control. This sets the DOWN (close) limit and
begins opening the door.
NOTE:
If neither the black or the orange button is pressed, the door will
reverse off the floor and the DOWN travel limit will be set automatically.
4. Open and close the door with the remote control or door control 2 or
3 times.
• If the door does not stop in the desired UP (open) position or
reverses before the door stops at the DOWN (close) position,
repeat Setting the Limits and Force, see adjustment steps 26 and
27
.
• If the door stops in both the desired UP (open) and DOWN (close)
positions, proceed to
Test the Safety Reversal System.
HAVING A PROBLEM?
1. Opener doesn't operate from either door control or remote:
• Does the opener have electric power? Plug lamp into outlet. If it does-
n't light, check the fuse box or the circuit breaker. (Some outlets are
controlled by a wall switch.)
• Have you disengaged all door locks? Review installation instruction
warnings on page 1.
• Is there a build-up of ice or snow under door? The door may be frozen
to ground. Remove any obstruction.
• The garage door spring may be broken. Have it replaced.
2. Opener operates from remote but not from door control:
• Is door control button lit? If not, remove the bell wire from the opener
terminals. Short the red and white terminals by touching both terminals
at the same time with a piece of wire. If the opener runs, check for a
faulty wire connection at the door control, a short under the staples, or
a broken wire.
• Are wiring connections correct? Review page 7.
3. Door operates from door control but not from remote:
• Replace battery if necessary.
• If you have two or more remotes and only one operates, review
Program Your Opener, Remote and Keyless Entry steps 22 and 24.
• Is the door control button flashing? The opener is in lock mode. If you
have a Multi-Function Door Control, push and hold the Lock button for
2 seconds. The door control button will stop flashing.
4. Remote has short range:
• Is battery installed?
• Change the location of the remote control on the car.
• A metal garage door, foil-backed insulation or metal siding will reduce
the transmission range.
5. Door reverses for no apparent reason and opener light doesn't
blink:
• Is something obstructing the door? Pull manual release handle.
Operate door manually. If it is unbalanced or binding, call for profes-
sional garage door service.
• Clear any ice or snow from garage floor area where garage door clos-
es.
• Repeat Setting Limits and Force, see adjustment steps 26 and 27.
Repeat safety reverse test after adjustment is complete.
6. Door reverses for no apparent reason and opener light blinks for
5 seconds after reversing:
Check The Protector System™ (if you have installed this accessory).
If the light is blinking, correct alignment.
7. Opener noise is disturbing in living quarters
of home:
If operational noise is a problem because of proximity of the opener to
the living quarters, Vibration Isolator Kit 41A3263 can be installed. This
kit was designed to reduce the "sounding board effect" and is easy to
install.
8. The garage door opens and closes by itself:
Make sure remote push button is not stuck "on".
9. Door stops but doesn't close completely:
Repeat Setting the Limits, see adjustment step 26.
Repeat safety reverse test after any adjustment of door arm length,
close force or down limit.
10. Door opens but won't close:
• Check The Protector System™ (if you have installed this accessory). If
the light is blinking, correct alignment.
• If opener light does not blink and it is a new installation, repeat Setting
the Limit and Force steps 26 and 27.
Repeat the safety reverse test after the adjustment is complete.
11. Opener light does not turn on:
Replace light bulb (230V/40W maximum). Replace burned out bulbs with
rough service light bulbs.
7-en
