manualshive.com logo in svg

Chamberlain LiftMaster Professional SW420, Руководство пользователя

Поделиться
Скачать
Chamberlain LiftMaster Professional SW420 Скачать руководство пользователя страница 18

18

RPM SENSOR (HALL EFFECT) ADJUSTMENT

NOTE:

 Normally the RPM sensor (hall effect) does not need 

adjustment, but may go out of alignment due to shipping 
vibration or rough handling.

These operators use an internal entrapment protector system. 
This system consists of the control board, magnet, and RPM 
sensor. It may become necessary to adjust the sensor for correct 
alignment. To do so please perform the following steps:

1.   Loosen the two screws holding the hall bracket to the frame.

2.   Adjust the bracket so that the sensor is:

 

a. Parallel with the pulley.

 

b.  .020" (.051 cm) away from the pulley’s magnet. Use a 

feeler gauge to measure the distance.

3.   Tighten screws to secure assembly.

4.   Manually rotate pulley to ensure that each magnet clears the 

sensor board.

If a magnet does not clear the board, re-adjust the RPM
(hall effect) assembly accordingly.

A D J U S T M E N T

To reduce the risk of SEVERE INJURY or DEATH:

•  Disconnect power BEFORE performing ANY adjustments.

ATTENTION

AVERTISSEMENT

AVERTISSEMENT

AVERTISSEMENT

WARNING

WARNING

CAUTION

WARNING

WARNING

PRECAUCIÓN

ADVERTENCIA

ADVERTENCIA

ADVERTENCIA

Cable

Operator Chassis

Mounting 
Screws (2)

Bracket

Pulley 
Magnet

Pulley

Содержание LiftMaster Professional SW420





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды