Chamberlain LiftMaster Professional SW420 Скачать руководство пользователя

Страница: 12 / 36

CONTROL ARM ASSEMBLY

1. Assemble the control arm to the operator hub.

2. Push up the manual release pin from below the hub and

through the control arm. Retain in place with clevis pin. Use
3/8" washers to reduce play between the clevis pin and the top
of the control arm.

3. When the manual release pin is allowed to drop down, the

control arm should swivel freely about the hub. Leave the arm
free to pivot at this time.

4. Fasten the arm stop to the extension arm. Left hand or right

hand installations call for mounting the arm stop on opposite
sides of the extension arm.

5. Secure the extension arm to the control arm using the

hardware provided.

6. Assemble the gate bracket to the extension arm as shown.

7. Put the gate in the fully closed position and extend the arm

assembly out to the closed gate. Mark the point on the gate
where the gate bracket will mount to the gate.

8. The gate bracket must be installed on a structural member of

the gate. If require, install a horizontal support on the gate at
the appropriate height.

9. Attach the gate bracket with U-bolts or by welding.

Figure 2

Figure 1

I N S T A L L A T I O N

If the arm stop is installed incorrectly, the gate will be
prevented from opening and damage to the operator may
result!

ATTENTION

AVERTISSEMENT

WARNING

CAUTION

WARNING

PRECAUCIÓN

ADVERTENCIA

Arm Stop
(Right Open)

Arm Kit 307072703R

Drive Hub
Disconnect Kit
K75-18625

Control Arm

(As Required)

Drive Hub
on Operator

Arm Stop Kit
K75-18624

Gate Bracket
Bolt Kit
K75-19314

Extension Arm

Arm Stop
(Left Open)

Gate Bracket

Gate

Control
Arm

Extension Arm

Hinge Pin

28"

Gate Bracket

36-1/2"
(Approximately)

33-1/2"

16"

26"

Arm Stop

Fence

Operator Shaft

Содержание LiftMaster Professional SW420





































Результаты поиска

Содержание LiftMaster Professional SW420

Отзывы:

Похожие инструкции для LiftMaster Professional SW420

Бренды по названию

Популярные бренды

Chamberlain LiftMaster Professional SW420, Руководство по установке

Результаты поиска

Содержание LiftMaster Professional SW420

Отзывы:

Похожие инструкции для LiftMaster Professional SW420

Бренды по названию

Популярные бренды