Chamberlain LiftMaster Elite Security+ 3850 Скачать руководство пользователя страница 7

Страница: 7 / 40

ASSEMBLY STEP 3

Attach the Belt Cap Retainer

• Position the belt cap retainer over the motor unit belt pulley so

the three holes in cap align with the three holes in mounting
plate. Attach with #8x3/8" hex screws provided.

You have now finished assembling your garage door opener.
Please read the following warnings before proceeding to the
installation section.

INSTALLATION

8x3/8" Hex Screws

Belt Cap Retainer

Mounting Plate

Motor Unit Belt Pulley

To avoid possible SERIOUS INJURY to fingers from moving
garage door opener:
• ALWAYS keep hand clear of belt pulley while operating

opener.

• SECURELY attach belt pulley cover BEFORE operating.

Hex Screw
#8x3/8"

HARDWARE SHOWN ACTUAL

SIZE

WARNING

IMPORTANT INSTALLATION INSTRUCTIONS

1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND

INSTRUCTIONS.

2. Install garage door opener ONLY on properly balanced and

lubricated garage door. An improperly balanced door may not
reverse when required and could result in SEVERE INJURY or
DEATH.

3. ALL repairs to cables, spring assemblies and other hardware

MUST be made by a trained door systems technician BEFORE
installing opener.

4. Disable ALL locks and remove ALL ropes connected to garage

door BEFORE installing opener to avoid entanglement.

5.  Install garage door opener 7 feet (2.1 m) or more above floor.
6.  Mount emergency release handle 6 feet (1.8 m) above floor.
7.  NEVER connect garage door opener to power source until

instructed to do so.

8. NEVER wear watches, rings or loose clothing while installing

or servicing opener. They could be caught in garage door or
opener mechanisms.

9. Install wall-mounted garage door control:

• within sight of the garage door.

• out of reach of children at minimum height of

5 feet (1.5 m).

• away from ALL moving parts of the door.

10. Place entrapment warning label on wall next to garage door

control.

11. Place manual release/safety reverse test label in plain view

on inside of garage door.

12. Upon completion of installation, test safety reversal system.

Door MUST reverse on contact with a 1-1/2" (3.8 cm) high
object (or a 2x4 laid flat) on the floor.

13. To avoid SERIOUS PERSONAL INJURY or DEATH from

electrocution, disconnect ALL electric and battery power
BEFORE performing ANY service or maintenance.

To reduce the risk of SEVERE INJURY or DEATH:

Содержание LiftMaster Elite Security+ 3850









































Результаты поиска

Содержание LiftMaster Elite Security+ 3850

Отзывы:

Похожие инструкции для LiftMaster Elite Security+ 3850

Бренды по названию

Популярные бренды

Chamberlain LiftMaster Elite Security+ 3850, Руководство пользователя

Результаты поиска

Содержание LiftMaster Elite Security+ 3850

Отзывы:

Похожие инструкции для LiftMaster Elite Security+ 3850

Бренды по названию

Популярные бренды