Chamberlain LiftMaster Elite Security+ 3850 Скачать руководство пользователя страница 6

Страница: 6 / 40

ASSEMBLY STEP 1

Attach the Rail to the Motor Unit

To avoid installation difficulties, do not run the garage door
opener until instructed to do so.

• Remove the two washered bolts mounted on top of motor unit.

• Align rail and styrofoam over belt pulley. Cut tape from rail,

chain and styrofoam.

•

REMOVE STYROFOAM.

• Insert both washered bolts through the rail into the motor unit.

Tighten bolts securely.

Use only these bolts! Use of any other bolts will cause

serious damage to door opener.

• Position belt over the motor unit belt pulley.

To avoid SERIOUS damage to opener, ONLY use bolts
mounted in top of motor unit.

ASSEMBLY STEP 2

Set the Belt Tension

• By hand, thread the spring trolley nut on the threaded shaft

until it is finger tight against the trolley (Figure 1). Do not use
any tools.

• Insert a screwdriver tip into one of the nut ring slots and brace

it firmly against the trolley (Figure 2).

• Place a 7/16" open end wrench on the square end. Rotate

about 1/4 turn until the spring releases and snaps the nut ring
against the trolley (Figure 3).

This extends the spring for optimum belt tension.

Washered Bolt
5/16"-18x1/2"

Rail Hole

Motor Unit
Belt Pulley

Rail Hole

USE ONLY THIS

TYPE AND SIZE

BOLT

Trolley
Threaded
Shaft

Spring/Trolley Nut

Nut
Ring

Trolley
Threaded
Shaft

Nut Ring
Slots

Square
End

Nut Ring

Trolley

Nut Ring

Trolley

1" (2.5 cm)

1-1/4" (3.18 cm)

BEFORE

AFTER RELEASE

Figure 1

Figure 2

Figure 3

Содержание LiftMaster Elite Security+ 3850









































Результаты поиска

Содержание LiftMaster Elite Security+ 3850

Отзывы:

Похожие инструкции для LiftMaster Elite Security+ 3850

Бренды по названию

Популярные бренды

Chamberlain LiftMaster Elite Security+ 3850, Руководство пользователя

Результаты поиска

Содержание LiftMaster Elite Security+ 3850

Отзывы:

Похожие инструкции для LiftMaster Elite Security+ 3850

Бренды по названию

Популярные бренды