background image

31

NOTE:

 Your new Keyless Entry must be programmed to operate your garage door opener.

One Button Close: 

The garage door opener can be closed by pressing only the ENTER button if the one 
button close feature has been activated. This feature has been activated at the factory. 
To activate or deactivate this feature press and hold buttons 1 and 9 for 10 seconds. The 
keypad will blink twice when the one button close is active. The keypad will blink four 
times when one button close is deactivated.

Programming

To Add, Reprogram or Change a Keyless Entry PIN

USING THE “LEARN” BUTTON

 Press and release the purple “learn” button on garage door opener. The learn 
indicator light will glow steadily for 30 seconds.

Within 30 seconds, enter a four digit personal identifi cation number (PIN) of your 
choice on the keypad. Then press and hold the ENTER button.

Release the button when the remote light blinks. It has learned the code. If light bulbs 
are not installed, two clicks will be heard.

To change an existing, known PIN

If the existing PIN is known, it may be 
changed by one person without using a 
ladder.

1.  Press the four buttons for the present 

PIN, then press and hold the # button.

   The garage door opener light will blink 

twice. Release the # button.

2.  Press the new 4-digit PIN you have 

chosen, then press ENTER.

The garage door opener lights will blink 
once when the PIN has been learned.

Test by pressing the new PIN, then press 
ENTER. The door should move.

To set a temporary PIN

You may authorize access by visitors or 
service people with a temporary 4-digit PIN. 
After a programmed number of hours or 
number of accesses, this temporary PIN 
expires and will no longer open the door. It 
can be used to close the door even after it 
has expired. To set a temporary PIN:

1.  Press the four buttons for your personal 

entry PIN (not the last temporary PIN), 
then press and hold the 

✽ 

button.

   The remote light will blink three times. 

Release the button.

2.  Press the temporary 4-digit PIN you have 

chosen, then press ENTER. 

   The garage door opener light will blink 

four times.

3.  To set the number of hours this 

temporary PIN will work, press the 
number of hours (up to 255),
then press 

.

OR

3.  To set the number of times this 

temporary PIN will open door, press the 
number of times (up to 255), then 
press #.

The remote light will blink once when the 
temporary PIN has been learned.

Test by pressing the four buttons for the 
temporary PIN, then press ENTER. The 
door should move. If the temporary PIN 
was set to a certain number of openings, 
remember that the test has used up one 
opening. To clear the temporary password, 
repeat steps 1-3, setting the number of 
hours or times to 0 in step 3.

USING THE DOOR CONTROL

 Press the Prog <Learn> button on the door control.

Press the Prog <Learn> button again to confi rm Learn Mode.

Enter a four digit personal identifi cation number (PIN) of your choice on the keypad. 
Then press ENTER.

When the remote light blinks, it has learned the code. If light bulbs are not installed, 
two clicks will be heard.

1
2
3

4

1

2

3

1

2

3

1

2

3

4

Содержание LiftMaster Elite Security+ 3800PLD





































Отзывы: