manualshive.com logo in svg

Chamberlain GJ, Руководство пользователя, Страница: 6 / 20

Поделиться
Скачать
Chamberlain GJ Скачать руководство пользователя страница 6

 

6

 

INSTALL CONTROL STATION

W A R N I N G

TO PREVENT ENTRAPMENT

DO NOT START DOOR  DOWNWARD

UNLESS DOORWAY IS CLEAR

OPEN

CLOSE

STOP

Control Station

WARNING Notice

Push

Buttons

The Chamberlain Group, Inc.
Install Control Station (Three Button Art)
MJ CDO #2 (Green)
6/20/91 

WARNING

CAUTION

WARNING

WARNING

CAUTION

WARNING

DISCONNECT POWER AT THE FUSE BOX BEFORE
PROCEEDING.
OPERATOR MUST BE PROPERLY GROUNDED AND
CONNECTED IN ACCORDANCE WITH LOCAL
ELECTRICAL CODES. NOTE: THE OPERATOR
SHOULD BE ON A SEPARATE FUSED LINE OF
ADEQUATE CAPACITY.
ALL ELECTRICAL CONNECTIONS MUST BE MADE
BY A QUALIFIED INDIVIDUAL.

WARNING

CAUTION

WARNING

WARNING

CAUTION

WARNING

TO AVOID DAMAGE TO DOOR AND OPERATOR,
MAKE ALL DOOR LOCKS INOPERATIVE. SECURE
LOCK(S) IN "OPEN" POSITION.
IF THE DOOR LOCK NEEDS TO REMAIN
FUNCTIONAL, INSTALL AN INTERLOCK SWITCH.

WARNING

CAUTION

WARNING

WARNING

CAUTION

WARNING

INSTALL THE CONTROL STATION WHERE THE
DOOR IS VISIBLE, BUT AWAY FROM THE DOOR AND
ITS HARDWARE. IF CONTROL STATION CANNOT BE
INSTALLED WHERE DOOR IS VISIBLE, OR IF ANY
DEVICE OTHER THAN THE CONTROL STATION IS
USED TO ACTIVATE THE DOOR, 

A REVERSING

EDGE  MUST BE INSTALLED ON THE BOTTOM OF
THE DOOR. FAILURE TO INSTALL A REVERSING
EDGE UNDER THESE CIRCUMSTANCES MAY
RESULT IN SERIOUS INJURY OR DEATH TO
PERSONS TRAPPED BENEATH THE DOOR.

1.

Complete electrical connections to the operator
and the control station. Fasten the control station
to the wall and MOUNT THE WARNING NOTICE
BESIDE OR BELOW THE PUSH BUTTON
STATION.

2.

Apply power to the operator. Press OPEN push
button and observe direction of output shaft
rotation. See Figure 4, page 4. Press the STOP
button.

If shaft does not rotate in the correct direction,
check for improper wiring at the control station or
between operator and control station.

If the operator is three phase and control station
wiring is correct, exchange any two of the three
incoming power leads.

If electrical problems persist, call our Toll Free
number for assistance (1-800-528-6563).

CABLE CONNECTION NOTE:

Be sure to use the control box opening with the 
1-1/16" hole for the POWER cable. All control wires
use the 7/8" hole.

Refer to Master Wiring Diagram. Make connection
through holes labeled for power and control. Do
not run control wires in the same conduit as
power wires.

Before installing control station be sure to follow all warnings described below.  Failure to so may result
in severe injury to persons and/or damage to operator.  Do not install any wiring or attempt to run the
operator without consulting the wiring diagram.  Install the optional Reversing Edge before proceeding
with the Control Station installation.

IMPORTANT: Mount WARNING NOTICE beside or
below the push button station.

IMPORTANT SAFETY NOTES

CONTROL STATION WIRING

MOUNT WARNING NOTICE

7/8" Hole (far side)

 for low voltage

CONTROL WIRES

1-1/16" Hole (near side)

 for high voltage

POWER WIRES

Содержание GJ





















Отзывы:

Нет отзывов