manualshive.com logo in svg

Chamberlain GJ, Руководство пользователя, Страница: 3 / 20

Поделиться
Скачать
Chamberlain GJ Скачать руководство пользователя страница 3

CAUTION

CONNECT REVERSING EDGE

SWITCH - SEE INSTALLATION

INSTRUCTIONS

FOR INDOOR USE ONLY

INSTALL MORE THAN 8 FT. ABOVE DOOR

LOCATE CONTROL STATION SO THAT DOOR IS WITHIN

SITE OF PERSON OPERATING THE CONTROL. DOOR

MUST BE CONTROLLED BY 3 BUTTON STATION

Cotterpin

Disconnect Lever

Cutout for Rollpin

(typical both sides)

Hand

Chain Wheel

Chain Guide

3

2-1/4"

FIGURE 1

Shaft Support Bracket
with Bearing (Not Supplied)
Door Sprocket

TO AVOID DAMAGE TO DOOR AND OPERATOR,
MAKE ALL DOOR LOCKS INOPERATIVE. SECURE
LOCK(S) IN "OPEN" POSITION.

IF THE DOOR LOCK NEEDS TO REMAIN
FUNCTIONAL, INSTALL AN INTERLOCK SWITCH. 

DO NOT CONNECT ELECTRIC POWER UNTIL
INSTRUCTED TO DO SO.

KEEP DOOR BALANCED. STICKING OR BINDING
DOORS MUST BE REPAIRED. DOORS, DOOR
SPRINGS, CABLES, PULLEYS, BRACKETS AND
THEIR HARDWARE MAY BE UNDER EXTREME
TENSION AND CAN CAUSE SERIOUS PERSONAL
INJURY. CALL A PROFESSIONAL DOOR
SERVICEMAN TO MOVE OR ADJUST DOOR
SPRINGS OR HARDWARE.

WARNING

CAUTION

WARNING

WARNING

CAUTION

WARNING

WARNING

CAUTION

WARNING

WARNING

CAUTION

WARNING

SITE PREPARATIONS

It is imperative that the wall or mounting surface
provide adequate support for the operator.
This surface must:

a) Be rigid to prevent play between operator and 

door shaft.  

b) Provide a level base.
c) Permit the operator to be fastened securely and

with the drive shaft parallel to the door shaft. 

The safety and wear of the operator will be adversely
affected if any of the above requirements are not met.  

For metal buildings, fasten 2” x 2” x 3/16” (or larger)
angle iron frames to the building purlins.  Retain
2-1/4” between frames.  See Figure 1.

The GJ operator may be mounted on either the right (standard) or left side of door, and in either a vertical
(standard) or horizontal mounting position.  Refer to the steps below if you require the hand chain and/or
disconnect chain to be on the opposite side of the operator; Or if the operator is being mounted in a horizontal
position.

MOUNTING CONVERSIONS

Hand Chain Right/Left Conversion
Remove the two snap rings (1 pc. outer, 1 pc inner)
on hand chain shaft assembly.  Position roll-pin to fit
through cutout in frame and slide complete shaft
assembly through housing and bevel gear.  Insert
shaft assembly on opposite side of housing,  and
replace bevel gear, bearing, hardware, and snap rings
on the opposite side of shaft in the same manner.

Disconnect Lever Right/Left Conversion
Remove cotter pins on the ends of the disconnect
shaft (square shaft), move the disconnect lever arm to
the opposite side, and replace the cotter pins.  Be
sure to keep two(2) 12ga. washers on the side without
the lever arm.

Horizontal Mounting Conversion
Remove cotter pins on the ends of the disconnect
shaft (square shaft), and remove lever.  Replace lever
using square hole on opposite end of lever.
Reposition sash chain to opposite end of lever also.
Replace cotterpins.

IMPORTANT SAFETY NOTES

FIGURE 2

Содержание GJ





















Отзывы:

Нет отзывов