manualshive.com logo in svg

Chamberlain GJ, Руководство пользователя, Страница: 4 / 20

Поделиться
Скачать
Chamberlain GJ Скачать руководство пользователя страница 4

 

4

1a.

 

Wall Mounting
The operator should generally be installed below
the door shaft, and as close to the door as
possible. The optimum distance between the door
shaft and operator drive shaft is between 12” - 15”.
On concrete buildings, attach a shaft support
bracket to the wall of the building.  Refer to Figure 3.

OPERATOR MOUNTING

IMPORTANT: An additional wall mounting
plate (P/N 10-9098) or equivalent is
recommended to provide additional support
and to allow for adjustment of the drive chain. 

IMPORTANT: The shelf or bracket must
provide adequate support, prevent play
between operator and door shaft, and permit
operator to be fastened securely and with the
drive shaft parallel to the door shaft.

1b. Bracket or Shelf Mounting 

The operator may be mounted either above or
below the door shaft.  The optimum distance
between the door shaft and operator drive shaft is
between 12” - 15”.   Refer to Figure 4.

1c. Place door sprocket on the door shaft.  Do not

insert the key at this time.

2.

Place drive sprocket on the appropriate side of
the operator. Do not insert the key at this time.

3.  Wrap drive chain around door sprocket and join

roller chain ends together with master link.

4.

Raise operator to approximate mounting position
and position chain over operator sprocket.

5.

Raise or lower operator until the chain is taut (not
tight). Make sure the operator output shaft is
parallel to door shaft and sprockets are aligned.
When in position, secure the operator to wall or
mounting bracket.

6.

Align sprockets and secure, (see Figure 5).

Mount Door Sprocket to Door.
Sprocket Supplied with Door,
(Not with Operator).
Refer to Door Owner's Manual
for Installing Door Sprocket

Installation of Operator to
Sheet Type Rolling Doors 
or Rolling Doors without
Live Drive Shaft

Door

Sprocket

Mounting

Bracket

(Optional)

Drive

Sprocket

Direction of Output Shaft

Rotation for OPEN

FIGURE 4

FIGURE 3

The standard GJ operator is setup for mounting on right side of the door and in vertical position. If necessary,
refer to the operator mounting conversions on page 3.  Refer to the illustrations and instructions below that suits
your application.

Be sure door sprocket
is properly aligned with
drive sprocket before
securing to shaft.

FIGURE 5

Содержание GJ





















Отзывы:

Нет отзывов