Chamberlain ACXL Скачать руководство пользователя страница 2

2

To reduce the risk of SEVERE INJURY or DEATH:
•  Disconnect power at the fuse box BEFORE proceeding. 
•  To AVOID damaging gas, power or other underground utility 

lines, contact underground utility locating companies BEFORE 
digging.

•  ALL electrical connections MUST be made by a qualified 

individual.

•  ALL power and control wiring MUST be run in separate 

conduit.

To protect against fire and electrocution:
•  Disconnect power BEFORE installing or servicing controller.

•  NEVER connect a keypad/reader or lock to doors without first 

consulting the applicable fire code.

•  You MUST consult with, and get approval from, local fire 

officials BEFORE installing locks or devices on ANY doors that 
may be fire exits. 

•  Use of egress push buttons may not be legal. Single action 

exits may be required.

•  ALWAYS obtain proper permits and approvals in writing 

BEFORE installing equipment.

Safety

Safety Symbol and Signal Word Review 

When you see these Safety Symbols and Signal Words on 
the following pages, they will alert you to the possibility of 
serious injury or death if you do not comply with the warnings 
that accompany them. The hazard may come from something 
mechanical or from electric shock. Read the warnings carefully.

When you see this Signal Word on the following pages, it will alert 
you to the possibility of damage to your property or product if you 
do not comply with the cautionary statements that accompany it. 
Read them carefully.

MECHANICAL

ELECTRICAL

Содержание ACXL
















Отзывы: