Chamberlain AccessMaster M100 Скачать руководство пользователя

Страница: 6 / 36

ASSEMBLY STEP 1

Attach the T-Rail to the Motor Unit

To avoid installation difficulties, do not run the
garage door opener until instructed to do so.

• Remove the two washered bolts mounted in top of

motor unit.

• Position T-rail at a 45˚ angle to opener so one hole

in T-rail and motor unit line up.

• Thread one of the washered bolts part way in.

Use only these bolts! Use of any other bolts will
cause serious damage to door opener.

• Align T-rail and styrofoam over sprocket. Cut tape

from T-rail, chain and styrofoam.

• REMOVE STYROFOAM.

USE ONLY THIS
TYPE AND SIZE
BOLT

Washered bolt
5/16"-18x1/2"

Styrofoam

T-rail
Hole

To avoid serious damage to opener, ONLY use bolts
mounted in top of motor unit.

WARNING

CAUTION

WARNING

ASSEMBLY STEP 2

Attach the Chain to the Sprocket
and Install the Sprocket Cover

• Position chain over the sprocket. If necessary,

loosen the outer nut on the trolley to obtain more
chain slack.

• Insert the second washered screw.

CAUTION: Use

only the bolt previously removed from motor
unit!

• Tighten both bolts securely through the T-rail into

the motor unit as shown.

• Install the sprocket cover: Insert the back tab in the

slot. Squeeze the cover slightly and insert the front
tab in the slot on the mounting plate.

Proceed to Assembly Step 3.

To avoid possible SERIOUS INJURY to fingers from
moving garage door opener:
• ALWAYS keep hand clear of sprocket while operating

opener.

• Securely attach sprocket cover before operating.

WARNING

CAUTION

WARNING

USE ONLY THIS
TYPE AND SIZE
BOLT

Washered bolt
5/16"-18x1/2"

Sprocket

Sprocket Cover

Mounting
Plate

Front Tab Slot

Back Tab Slot

Содержание AccessMaster M100





































Результаты поиска

Содержание AccessMaster M100

Отзывы:

Похожие инструкции для AccessMaster M100

Бренды по названию

Популярные бренды

Chamberlain AccessMaster M100, Руководство пользователя

Результаты поиска

Содержание AccessMaster M100

Отзывы:

Похожие инструкции для AccessMaster M100

Бренды по названию

Популярные бренды