Chamberlain 8355W Скачать руководство пользователя | Manualshive

Страница: 32 / 52

background image

32

Battery Backup

Charge the Battery*

The battery charges when the garage door opener is plugged into a 120Vac electrical outlet that has
power and requires 24 hours to fully charge. A fully charged battery supplies 12Vdc to the garage
door opener for one to two days of normal operation during an electrical power outage. After the
electrical power has been restored, the battery will recharge within 24 hours. The battery will last
approximately 1 to 2 years with normal usage. Instructions for replacement are provided with the
battery. To obtain maximum battery life and prevent damage, disconnect the battery when the garage
door opener is unplugged for an extended period of time, such as a summer or winter home.

NOTE:

When the garage door opener is in battery backup mode the garage door opener lights, Timer-

to-Close, and Remote Close features are unavailable.
In battery backup mode, the Automatic Garage Door Lock will unlock when the garage door is
opened, and will remain disabled until power is restored.

* If applicable

Battery Status LED

GREEN LED:

All systems are normal.

• A solid green LED light indicates the battery is fully charged.
• A flashing green LED indicates the battery is being charged.

ORANGE LED:

The garage door opener has lost power and is in battery backup mode.

• A solid orange LED with beep, sounding approximately every 2 seconds, indicates the garage

door opener is operating on battery power.

• A flashing orange LED with beep, sounding every 30 seconds, indicates the battery is low.

RED LED:

The garage door opener's 12V battery needs to be replaced.

• A solid red LED with beep, sounding every 30 seconds, indicates the 12V battery will no

longer hold a charge and needs to be replaced. Replace the battery back up to maintain the
battery backup feature.

NOTE:

The Battery Status LED is most visible with the garage door opener light off. Battery does not

have to be fully charged to operate the garage door opener.

Battery Status LED

«
...
30
31
32
33
34
...
»

Содержание 8355W





















































Отзывы:

Нет отзывов

Похожие инструкции для 8355W

Бренд: GATEXPERT Страницы: 22

Бренд: GBD Страницы: 80

AXOVIA 220B RTS

Бренд: SOMFY Страницы: 68

Бренд: Motorline professional Страницы: 8

Бренд: Kitchen Mama Страницы: 5

Бренд: Key Automation Страницы: 48

Бренд: CAME Страницы: 64

Бренд: SOMFY Страницы: 60

Бренд: SOMFY Страницы: 80

Бренд: Nice Страницы: 2

Бренд: Nice Страницы: 11

Бренд: fadini Страницы: 8

Бренд: Jaytech Страницы: 19

Бренд: FlexiForce Страницы: 30

Бренд: gourmetmaxx Страницы: 8

Бренд: TOPP Страницы: 60

IntelliSwing IQ-500-S

Бренд: IQ Gate Systems Страницы: 29

Бренд: Beninca Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды