Challenger Lifts CL16 Series Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 26

background image

Model CL16

Installation, Operation and Maintenance

Page

8

Rev. 08/24/2021

CL16-IOM-A.doc

STANDARD

6" REDUCED (-6")

12" REDUCED (-12")

STANDARD

6" REDUCED (-6")

12" REDUCED (-12")

STANDARD

6" REDUCED (-6")

12" REDUCED (-12")

STANDARD

6" REDUCED (-6")

12" REDUCED (-12")

Fig. 10 – Cable Attachment At The Carriage

30) Mount synchronizer cables to carriages as

shown in

Fig. 10

.

Note: Use the proper Take-

Up Tube as shown in Fig 10 based on the
width of the lift.

H

YDRAULICS

IMPORTANT: To ensure proper hose fitting seal
without damage to the fitting follow this
procedure for each hose connection:

Screw flared

fitting on finger tight. Rotate flared fitting 1 1/2 hex
flats (90 deg.). Back the flared fitting off one full turn.
Again tighten flared fitting finger tight, then rotate
flared fitting 1 1/2 hex flats (90 deg.).

31) Mount Power Unit to power column as shown in

Fig 11

. The mounting hardware, (4) 5/16”-18NC

hex nuts, are pre-installed on power unit
mounting bracket.

Fig. 11 – Power Unit Mounting

32) Install 9/16”-18 O-ring elbow (

in hardware box

) into

power unit,

Fig. 11

.

CAUTION

do not damage

rubber O-ring.

33) Install the block hose clamp bracket onto both

column extensions using 1/4”-20NC x 3/4” lg.
hex flange bolt and nut, see

Fig 12

.

«
...
6
7
8
9
10
...
»

Содержание CL16 Series



























Отзывы:

Нет отзывов

Похожие инструкции для CL16 Series

Бренд: Lampert Страницы: 18

Бренд: WAGO Страницы: 56

Бренд: Vestil Страницы: 11

Бренд: Keg King Страницы: 4

SystemRoMedic EvaDrive450

Бренд: Handicare Страницы: 37

SC Express Series

Бренд: National Instruments Страницы: 36

Бренд: heat-timer Страницы: 40

Бренд: National Instruments Страницы: 13

Бренд: Bame Страницы: 12

iNELS Air AirIM-100S

Бренд: Elko Страницы: 8

Бренд: Chicago Electric Страницы: 2

Бренд: SPT Страницы: 32

ISaGRAF VP-2117

Бренд: ICP DAS USA Страницы: 75

Бренд: PROLIFTS Страницы: 44

VANTAGE SVM178-B

Бренд: Lincoln Electric Страницы: 278

Бренд: Reechcraft Страницы: 56

Бренд: Eagle Страницы: 16

Бренд: National Instruments Страницы: 77

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды