background image

 

 

10   

CET Electric Technology 

 

Figure 4-3 Login Interface

 

5)

 

Once the log-in credentials are confirmed, the following page appears. 

 

Figure 4-4 Basic Settings

 

4.2 Ethernet 

The 

P1 (Ethernet)

 port’s settings can be configured here based on the actual situation. Click 

Save

 to 

confirm your changes. Please be reminded that the 

IP Address

 and 

Default Gateway

 for the Ethernet 

port should be in the same subnet.     

 

 

Figure 4-5 P1 Settings

 

4.3 Serial Port   

The  PMC-1302  comes  standard  with  two  RS-485  ports:  P2  and  P3.  All  setup  parameters  such  as 

Baudrate

Data  Bits

Parity

Stop  Bits

IP  Port

  and 

Timeout

  can  be  configured  here  to  match  the 

settings of the downstream RS485 devices. Please be reminded that the 

IP Port 

number of the Serial 

Gateway feature for P2 (default = 20000) and P3 (default = 20001) should be different. Click

 Save

 to 

confirm  your  changes.  The  following  table  shows  the  setup  parameters  for  P2  and  P3.  Most  setup 
parameters are basic and self-explanatory. Please note that the 

Packet

 

Timeout (ms)

 parameter refers 

to  the  timeout  setting  for  the  IP  connection  instead  of  the  serial  connection,  meaning  that  the  IP 
connection  will  be  closed  if  there  are  no  activities  between  the  application  software  and  the 
PMC-1302  ESG  for  the  specified  amount  of  time.  This  is  to  prevent  a  potential  lock  up  of  the  IP 
connection at the PMC-1302 ESG if the application software fails to close the IP connection for some 
unknown reasons. It is recommended that the default 

Packet

 

Timeout

 of 300 seconds be used. 

Содержание PMC-1302





















Отзывы: