Cermetek Microelectronics, Inc.
High Speed Internet Modem Family
2005 Cermetek Microelectronics, Inc.
Page 6
Document No. 607-0017 Revision I1 (05/05)
Table 1. Summary of CH2124/60 Allowed @T
®
Commands.
Command Notes
Description
@T
[
A1
][
=n
]
1,2,3,4
Enter destination email address,
n
. Maximum length is 34 ASCII characters.
@T
[
D
][]
1,2,7,12 Dialup ISP and send pre-configured Input Port Status email. Message type sent is specified
by
@TJn
command or by
K8
parameter for firmware versions 1.262 or greater.
@T
[
DG
][
n
]
1,2,12
Dial preprogrammed ISP and Retrieve mail message from preprogrammed email address.
Message number must be specified,
n=1
to
99
.
@T
[
DK
][
n
]
1,2,12
Dial preprogrammed ISP and Delete mail message n.
n=aa
Where
aa
is the message number.
n=aa-bb
will delete message number
aa
through
bb
(inclusive).
n=*
will delete all messages.
@T
[
DM1
][]
1,2,3,4,
7,12
Dialup ISP and send user defined email message regardless of message type specified by
@TJn
command.
@T
[
E1
][
=n
]
1,2,3,4
Enter local or “FROM:” email address,
n
.
@T
[
H
][]
1,2
Directs remotely accessed iModem connected via Remote Dial-up Access to terminate
access session and hang-up.
@T
[
J
][
0
]
1,2,7,12 Establish email message type to be sent when iModem SEND pin is activated or the
@TD
command issued.
J0
will select the Input Port Status message or by
K8
parameter for
firmware versions 1.262 or greater.
@T
[
J
][
1
]
1,2,7,12 Establish email message type to be sent when iModem SEND pin is activated or the
@TD
command issued.
J1
will select the User Defined message or by
K8
parameter for firmware
versions 1.262 or greater.
@T
[
K0
][
=n
]
1,2,6
Select PAP Authentication Protocol:
n=01
allows PAP only. (DEFAULT)
n=7D
allows CHAP or PAP. (CHAP NOT SUPPORTED)
@T
[
K1
][
=n
]
1,2,6
Set the number of dial-up attempts. Auto re-dial enabled for
K1>01
. Specified in HEX.
n=01
allows initial dial-up attempt only (default).
n=0E
allows 15 dial-up attempts (maximum per FCC).
@T
[
K2
][
=n
]
1,2,6
Set the number of minutes,
n
, between auto-redials. Specified in HEX.
n=01
1 minute between re-dial attempts (default).
n=FF
255 minutes between re-dial attempts (maximum).
@T
[
K3
][
=n
]
1,2,6,10 Set the number of MESSAGE ACCEPTEDs required to exit auto-redial mode. Specified in
HEX.
n=01
1 MESSAGE ACCEPTEDs to exit auto re-dial (default).
n=FF
255 “accepted message” to exit auto re-dial (maximum).
@T
[
K4
][
=n
]
1,2,6,8 Select login method for User Defined message.
K4
affects the currently ACTIVE ISP
CONFIGURATION profile only:
n=01
PPP login only. PPP protocol used for email data packets.
n=02
Enables ASCII Text Login. PPP protocol used for email data packets. Message sent
using TCP/IP.
n=03
Unix Shell login. No PPP protocol.
@T
[
K8
][
=n
]
1,2,6
Select Email Message type to be sent when SEND PIN is set TTL low. Replaces
@TJ0
and
@TJ1
for firmware revisions 1.262 and greater:
n=30
Send Input Port Status message.
n=31
Send User Defined message. (Default)
